GITR-3BX 3-Button Remote
GITR-3BX Programming Instructions
GITR-3BX REMOTE TRANSMITTER INSTRUCTIONS
1- IMPORTANT INFORMATION
A unique transmitter code is set at the factory for each INTELLICODE® transmitter.
2- BATTERY INSTALL/REPLACEMENT
1. To open the case, gently push straight out on the battery cover lock tab as shown, Fig. 1.
2. Slide open battery cover. (New install) Make sure the new battery is facing the proper direction. Match battery polarity with symbols inside battery housing, Fig. 2. • Insert the new battery. (Replacement) Recommended replacement battery type: Alkaline A23, 12 volt. • Remove the old battery and insert the new battery.
3. Slide battery cover back in place until it clicks shut.
4. To confirm power, press any remote button. LED should come ON. For replacement battery, NO re-programming is needed
3- PROGRAM THE RECEIVER
1. Locate the Learn Code button and Radio Signal indicator LED on the powerhead of your door operator, Fig. 3A & B.
2. Press and release the Learn Code button. • The Radio Signal LED indicator will blink approximately 2 times per second.
3. Press a transmitter button once within 30 seconds. • The LED indicator stays lit - SOLID.
4. Press the same transmitter button again within 30 seconds.
• LED light indicator will go out.
• Remote is now programmed and ready for use.
5. Press the same Transmitter Button again and the door will move.
Repeat Steps 2 through 4 for each transmitter to be learned.
NOTE: Only ONE button of this MultiButton Transmitter can be programmed into a single door operator. The other buttons are to control other door operators.
NOTE: A maximum of 7 Transmitter, Wireless Keypad, and other access device codes can be stored into the receiver memory at one time. If a Transmitter becomes lost or if you want to delete a Transmitter proceed to ERASING ALL RECEIVER MEMORY.
4- ERASING ALL RECEIVER MEMORY
1. Press and HOLD the Learn Code button for 10 seconds or until Radio Signal LED indicator goes out. ALL Transmitter Codes are erased from Receiver (powerhead) memory.
2. Reprogram the Receiver with the remaining Transmitter Codes (Repeat Section 3 steps 2 through 4).
3. Reprogram the Receiver with any Wireless Keypad and other access device Codes using the instructions accompanying those devices.
5- TRANSMITTER OPERATION
• Point Transmitter at the garage door and press the button. The door will move.
• Press the Transmitter Button again and the door will stop.
• Press the Transmitter Button again and the door will move the other way. The door automatically stops at the end of the open or close cycle.
Replacement Transmitter Recommendation | |||
Model Number: | GITR-3BX | ||
Part Number: | 37517S | ||
Description: | 3-Button, Intellicode® 390 MHz | ||
![]() |
|||
If you have any of the below transmitters, a replacement | |||
transmitter can be GITR-3BX. | |||
![]() |
![]() |
||
GICTD-1 | GICTD-3 | ||
![]() |
![]() |
![]() |
|
GIT-1 or G2T-1 | GIT-2 or G2T-2 | 2 GIT-3 or G2T-3 | |
![]() |
![]() |
![]() |
![]() |
GICT390-1 | GICT390-3 | GMIC90-2 | GMIC90-3 |
![]() |
![]() |
![]() |
|
GIFT390-1 | GIT390-4 | GMI3 | |
(flashlight) | |||
![]() |
![]() |
![]() |
|
GIFTD-1 | GIFTD-3 | GITD-3 | |
(flashlight) | (flashlight) | ||
![]() |
![]() |
![]() |
|
GIC90-1 | GIC90-2 | GIC90-3 |
Don't see your remote? Click here for more compatibility options.
Questions & Answers
Ask a Question-
Will this remote work with a IS550/A?
Yes it will!
-
Will this work with 2020L
Yes it will!
-
Will this work with PMX500IC?
Yes! The GITR-3BX will work with the PMX500IC.
-
Will this work with a PMX500XL?
Yes it will!
-
will this work with 2024?
Yes it will!
-
Will this work with GPS1200IC
Yes, it will!
-
Will this work with H4000A?
Yes, this will work with a H4000A opener.
-
Will this work with Model IDS 990? The receiver model is ACSR4.
Yes! This will work with the ISD990 model garage door opener.
-
Will it work with a Overhead Legacy opener model 696CD/B
Yes, it will!
-
Will this work with model 3060L?
Yes, it will.
-
I have a GCG-350L am I correct in thinking this will NOT work with my opener? Which remote should I get?
This remote will work with your garage door opener. Any of our Intellicode remotes will.
-
Will this work with model # 1022
Yes, it is!
-
will this work with a PCG700ML? Do you have to know a code to setup the remote for an existing door opener?
This GITR-3BX will work with the PCG700ML model garage door opener. You do not need to know a code, you will program it by pressing the learn code button on the powerhead of the garage door opener. You can see more on the programming instructions here, and as always we are here to help if you need it. You can contact our Genie customer service at 1-800-354-3643.
-
Will this work with a pmxicb500
Yes, it will.
-
Will this work with a Linear opener
No, the GITR-3BX will not work with a Linear opener.
-
Will this remote work with a 1992 model genie garage door opener?
No, this will not work with a fixed code (dip switch) style garage door opener. You would need the Genie Master Remote.
-
We have a Genie ACSGT type 1 remote that is broken, will this work with it?
Yes, it will.
-
Will this work on a 1024
Yes, it will!
-
which replacement remote will with my Genie Screw Drive 1/2 HP SD 5050
You will need the Genie Master Remote, GM3T-R to work with the SD5050.
-
Will this work with Model CM86001C/A
Yes, it will!
-
My remote (GITR-3) has suddenly stopped working on my Model 2024 opener. Replaced battery and tried the reset steps to no avail. Please advise.
You can try to unplug the entire garage door opener and wait about one minute, then plug it back in. See if the remote works then. If not, it could be a few different issues causing this. You can contact customer service at 1-800-354-3643 for troubleshooting assistance.
-
will this work for a genie pro 7600ic/a opener
Yes, the GITR-3BX will work with the CM7600IC/A opener
-
Please tell me which button is what is useful. Cause on the new booklet that I received , on the new garage opener , it doesn’t explain what is used for the three button. The model number is GITR-3 Also is the light to the garage will be automatically off when the garage door close?
The 3 buttons on the remote can be used on additional Genie garage door openers, so you have the ability to work 3 different garage doors with Genie Intellicode systems. The lights on the garage door opener will time off within 4-6 minutes, depending on your model number. For any additional questions, please reach out to us here: http://overheaddoor.custhelp.com/app/ask. Thank you!