Skip to product information
1 of 1

The Genie Company

Optical Encoder (RPM Sensor) 39272T.S - Belt/ Chain Drive Models

Optical Encoder (RPM Sensor) 39272T.S - Belt/ Chain Drive Models

Regular price $24.99 USD
Regular price Sale price $24.99 USD
Sale Sold out

The Optical Encoder also sometimes called an RPM sensor, is compatible with the Genie model chain and belt drive garage door openers that are listed below. The optical encoder may help resolve problems of short traveling or issues with drifting limits on the garage door opener. 

  • Compatible with Genie models: 3020H, 3020H-B
  • Genuine Genie Replacement Part 

SKU: 39272T.S

In Stock! Usually ships within 24 hours.

ASK A QUESTION View full details
Optical Encoder (RPM Sensor) 39272T.S for Genie model Belt/ Chain Drive garage door openers, 3020H and 3020H-B
Optical Encoder (RPM Sensor) 39272T.S - Belt/ Chain Drive Models
$24.99

QUESTIONS & ANSWERS

Have a Question?

Be the first to ask a question about this.

Ask a Question

PDF Instructions for replacing the 39272T.S Optical Encoder 

These instructions are written assuming that you will have ample room around Opener to perform this repair. Some rare instances will require removal of the unit from it’s mounting hardware and repair made on a bench or floor. Refer to your Owners Manual or Installation Poster for proper assembly and carefully read and understand all warnings and cautions pertaining to your unit.

39272T.S 24V DC Opto Replacement For Chain & Belt Operators

WARNING
BE SURE ELECTRICAL POWER HAS BEEN DISCONNECTED FROM THE OPENER PRIOR TO REMOVING THE MOTOR COVER.

WARNING
ANY AND ALL REPAIRS MADE TO THIS UNIT MUST BE PERFORMED WITH THE DOOR DISCONNECTED FROM THE OPENER AND IN THE CLOSED POSITION.

Tools required: Standard slotted and Phillips head screwdrivers, small slotted screwdriver, 5/16” nut driver.

CLOSE THE GARAGE DOOR PRIOR TO REPAIR.

1. Remove power from the operator.

2. Press down on tabs to remove the lens.

3. Remove light bulbs.

4. Note locations and remove BWC (Basic Wall Control) and STB (Safe-T-Beam®) wires. Use a small screwdriver to press in on orange tabs to remove wires. FIG. 1.

39272T.S Optical Encoder replacement instructions, removing the wiring

5. If equipped, unplug and remove battery backup (BBU) from the back of motor housing. Fig. 2.

39272T.S Genie optical encoder replacement instructions

6. Using a 5/16” nut driver or common screwdriver, remove the 2 opener cover screws and remove opener cover. FIG-3A

39272T.S Optical encoder replacement for Genie garage door openers

7. Note the locations and disconnect lights, transformer primary, AC power, red & black motor wires, transformer secondary, and encoder harnesses. FIG. 4

Genie belt and chain drive garage door opener replacing the optical encoder 39272T.S

8. Using a 1/4” nut driver or common screwdriver, remove 2 control board mounting screws and then remove the control board. FIG. 5.

39272T.S optical encoder replacement for Genie belt and chain drive model garage door openers

9. Carefully remove all harnesses from the harness keepers.

10. Remove Opto Assembly cover screws (3-3/16”) leave harness plugged into assembly FIG. 3B.

11. Install replacement Opto Assembly and install cover screws (3).

12. Carefully slide all harnesses back into harness keepers.

13. Reinstall the control board, harnesses, and opener cover in reverse order. Ensure that harnesses are plugged in the correct positions. See harness detail FIG. 6.

14. Reinstall BWC & STB wires, light bulb, and lens.

15. Install BBU assembly onto motor housing if equipped.

16. Reapply power to the operator.

NOTE: Limit settings will require reprogramming. Refer to your owners manual for detailed instructions.

IMPORTANT: Test opener functions. The door MUST reverse on contact with a 1-1/2” high object (or a 2 x 4 board laid flat) at the center of the doorway on the floor. After adjusting either the force or limit of travel, retest door opener. Failure to adjust the opener properly may cause severe injury or death.

  • Shipping Truck

    Free Shipping

    We offer FREE shipping and handling on all orders that total over $17.99 and are shipped to a US address. All orders are shipped using UPS ground, directly from The Genie Company.

  • Genuine Genie Accessories and Parts

    Genuine Replacements

    Buying GENUINE Genie accessories and parts guarantees that you are getting quality OEM materials backed by a Genie warranty.

  • Customer support chat

    Support

    Need assistance? We are here for you! We offer a wide range of customer support options including contact by phone or email, web chat services with a live agent, and a robust support section also located on our website.  All customer care teams and services are based in the USA.

FREE SHIPPING ON ALL US ORDERS 17.99 AND UP