Skip to product information
1 of 1

The Genie Company

Optical Encoder (RPM Sensor) 39272R.S- Belt/Chain Drive Models

Optical Encoder (RPM Sensor) 39272R.S- Belt/Chain Drive Models

Regular price $23.31 USD
Regular price Sale price $23.31 USD
Sale Sold out

The Optical Encoder also called the RPM sensor, is used in certain Genie model chain and belt drive garage door openers. (See below for compatibility) This may resolve the issue of short travel problems or drifting limits on the garage door opener. 

  • Compatible with models; 1028, 2028, 1035, 2036 
  • If you do not see your model on this list and have questions please contact Genie for compatibility questions
  • Genuine Genie Replacement Part 

SKU: 39272R.S

In Stock! Usually ships within 24 hours.

ASK A QUESTION View full details
Optical Encoder (RPM Sensor) 39272R.S- Belt/Chain Drive Models ,  Service Parts - The Genie Company
Optical Encoder (RPM Sensor) 39272R.S- Belt/Chain Drive Models
$23.31

QUESTIONS & ANSWERS

Ask a Question
  • Is this a genuine replacement for a 1055 model garage motor?

    The part you listed is for the encoder only, for the motor on a Genie model 1055 you would need the motor 41521R.S.

PDF (Printable) Instructions for replacing the 39272R.S Optical Encoder

39272R.S DC Opto Replacement For Chain & Belt Operators

These instructions are written assuming that you will have ample room around Opener to perform this repair. Some rare instances will require removal of the unit from it’s mounting hardware and repair made on a bench or floor. Refer to your Owners Manual or Installation Poster for proper assembly and carefully read and understand all warnings and cautions pertaining to your unit.

WARNING
BE SURE ELECTRICAL POWER HAS BEEN DISCONNECTED FROM THE OPENER PRIOR TO REMOVING THE MOTOR COVER.

WARNING
ANY AND ALL REPAIRS MADE TO THIS UNIT MUST BE PERFORMED WITH THE DOOR DISCONNECTED FROM THE OPENER AND IN THE CLOSED POSITION.

Tools required: Standard slotted and Phillips head screwdrivers, small slotted screwdriver, 5/16” nutdriver.

NOTE: Rail not shown, rail removal is NOT necessary for this repair.

CLOSE DOOR PRIOR TO REPAIR.

1. Remove power from the garage door opener by unplugging it.

2. Press down on tabs to remove lens. FIG-1

39272R.S Genie optical encoder replacement instructions

3. Remove light bulb.

4. Note locations and remove BWC (Basic Wall Control) and STB (Safe-T-Beam®) wires. Use a small screwdriver to press in on orange tabs to remove wires. FIG-2

5. Using a 5/16” nut driver or common screw driver, remove the 3 opener cover screws and remove opener cover. FIG-2

Replacing the optical encoder 39272R.S on Genie garage door openers

 

6. Note the locations and disconnect lights, transformer primary, AC power, red & black motor wires, transformer secondary, and encoder harnesses. FIG-3

7. Using a 1/4” nut driver or common screwdriver, remove 2 control board mounting screws and remove control board. FIG-3

8. Carefully remove all harnesses from harness keepers. FIG-3

39272R.S Optical Encoder replacement instructions

9. Remove Opto Assembly cover screws (3-3/16”) leave harness plugged into assembly.

10. Install replacement Opto Assembly and install cover screws (3).

39272R.S Optical Encoder

11. Carefully slide all harnesses back into harness keepers.

12. Reinstall the control board, harnesses, and opener cover in reverse order. Ensure that harnesses are plugged in the correct positions. FIG-3, see connector detail.

13. Reinstall BWC & STB wires, light bulb and lens.

14. Reapply power to operator.

NOTE: Limit settings will require reprogramming. Refer to your owners manual for detailed instructions.

IMPORTANT: Test opener functions. The door MUST reverse on contact with a 1-1/2” high object (or a 2 x 4 board laid flat) at the center of doorway on the floor. After adjusting either the force or limit of travel, retest door opener. Failure to adjust the opener properly may cause severe injury or death.

  • Shipping Truck

    Free Shipping

    We offer FREE shipping and handling on all orders that total over $17.99 and are shipped to a US address. All orders are shipped using UPS ground, directly from The Genie Company.

  • Genuine Genie Accessories and Parts

    Genuine Replacements

    Buying GENUINE Genie accessories and parts guarantees that you are getting quality OEM materials backed by a Genie warranty.

  • Customer support chat

    Support

    Need assistance? We are here for you! We offer a wide range of customer support options including contact by phone or email, web chat services with a live agent, and a robust support section also located on our website.  All customer care teams and services are based in the USA.

FREE SHIPPING ON ALL US ORDERS 17.99 AND UP