The Genie Company
Intellicode® Receiver Board 36521S.S
Intellicode® Receiver Board 36521S.S
Couldn't load pickup availability
This Intellicode® receiver circuit board works with compatible Genie model garage door openers listed below. The receiver circuit board controls all wireless devices that are programmed into the garage door opener. Replacing this circuit board if you have determined it needs to be replaced, will get all your wireless devices working again quickly.
- Compatible with Genie Models: AMX300-IC/A, PMX300-IC/A, AMX500-ICA/, PMX500-IC/A, GPS700IC, GPS1200IC, PMX700, PMX1200
- Genuine Genie replacement part
- Wireless devices will need to be programmed to the new replacement circuit board once it is installed
SKU: 36521S.S
In Stock! Usually ships within 24 hours.
ASK A QUESTION View full details
QUESTIONS & ANSWERS
Ask a Question-
Will this work for model PMX300IC/B?
No, for Genie model PMX300IC/B only has one circuit board which would be the Control Board (3 Terminal Board).
-
Will this work on a CM8600IC/A
No, for model CM8600IC/A you would need 36521R.S receiver board.
-
How many remotes can i program?
You can program up to 7 wireless devices (this would include remotes, keypads, and in-vehicle remote systems).
-
Will this work with the ProMax PMX70?
Hello. No this board will not work with your Genie model PMX70 garage door opener. You will need the 20285R.S receiver.
-
Will this receiver board work with a H6000
Hello. No that board will not work. You would need part 36521R.S for your opener.
PDF Instructions for replacing the 36521S.S circuit board
REPLACEMENT 36521S.S RECEIVER BOARD INSTALLATION INSTRUCTIONS
For 390 MHz Stealth/Phantom Models
WARNING
Moving door can cause serious injury or death.
• During this procedure, the Door Opener could begin to run. Stay away from moving Door and its parts. To keep Door from moving, close Door and disconnect it from Opener by pulling Emergency Release Cord.
• Keep people clear of opening while the door is moving.
• Do Not allow children to play with remote control or door opener.
• Do Not operate a door that is jammed or has a broken spring.
If the safety reverse does not work properly:
• Close door/disconnect opener by pulling Emergency Release Cord.
• Do Not use the remote control or door opener.
• Refer to Door and Door Opener Owner’s Manuals or Instructions.
WARNING
BE SURE ELECTRICAL POWER HAS BEEN DISCONNECTED FROM THE INPUT POWER LINES PRIOR TO REMOVING THE ELECTRIC BOX COVER. AN APPROPRIATE LOCKOUT/TAGOUT PROCEDURE IS RECOMMENDED. INSURE THE DOOR IS CLOSED PRIOR TO REMOVING THE OPERATOR. TEST THE DOOR FOR PROPER OPERATION AND CORRECT ANY MALFUNCTIONS PRIOR TO REINSTALLING THE OPERATOR.
Tools Required: 1/4” nut driver or socket, and/or flat blade screwdriver.
1. UNPLUG operator from 110V outlet. If the unit is permanently wired, open the circuit breaker. If you are unsure about how to shut off power to the unit, call a licensed electrician in your area. Do not reconnect power until instructed to do so.
1. UNPLUG operator from 110V outlet.
2. REMOVE the 2 screws at the top of the light cover(s), flip the cover(s) down and loosen the 2 bottom screws. Remove the cover(s)
3. ON SIDE PLATE next to the antenna wire, loosen the 2 upper side panel screws and two lower screws on the front and back plates. Remove the side plate. FIG 1
4. REMOVE and retain the receiver mounting screw. FIGURE 2
5. UNPLUG wire harness from receiver board. Note harness orientation (Green wire on left facing the connector). FIGURE 3
6. INSTALL the receiver board to bracket and carefully insert board and bracket into position. Reinstall mounting screw. FIGURE 2
7. RECONNECT wire harness to replacement receiver board. FIGURE 3
8. FEED antenna wire through a slot in the rear panel and point downward. FIGURE 4
9. REPLACE side plate.
10. PLUG the power cord into the outlet (or reset breaker).
11. ADJUST up and downforce controls and program transmitter devices following all safety and operating instructions in the owners manual.
12. REINSTALL light cover.
-
Free Shipping
We offer FREE shipping and handling on all orders that total over $17.99 and are shipped to a US address. All orders are shipped using UPS ground, directly from The Genie Company.
-
Genuine Replacements
Buying GENUINE Genie accessories and parts guarantees that you are getting quality OEM materials backed by a Genie warranty.
-
Support
Need assistance? We are here for you! We offer a wide range of customer support options including contact by phone or email, web chat services with a live agent, and a robust support section also located on our website. All customer care teams and services are based in the USA.
