Free Shipping On All U.S. Orders $14.99 +
{"id":10552730115,"title":"Circuit Board \/ Series II Wall Console Bundle 38875R3.S","handle":"circuit-board-and-series-ii-wall-console","description":"\u003cp\u003e\u003cspan\u003eThis replacement circuit board with series II wall console is for certain Genie chain or belt drive models. Once you have determined your circuit board needs to be replaced\u003c\/span\u003e\u003cspan\u003e this board\/ wall console bundle will get your garage door opener back up and running quickly. \u003c\/span\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eCompatible with models 3022, 3024, 3042 (ChainMax 1000, SilentMax 1000, IntelliG 1000)\u003c\/li\u003e\n\u003cli\u003eReplaces old circuit board numbers - 38334R3.S, 38001R3.S\u003c\/li\u003e\n\u003cli\u003eGenuine Genie replacement parts\u003c\/li\u003e\n\u003cli\u003eRequires re-programming of limits and accessories with the new board \u003c\/li\u003e\n\u003cli\u003eAll remotes, keypads or wireless devices that you currently use will work with the new circuit board (after reprogramming)\u003c\/li\u003e\n\u003cli\u003eBundle Kit includes the replacement instructions, circuit board, and series II wall console  \u003c\/li\u003e\n\u003cli\u003eIf you had a Series III wall console (Gray with black buttons), when installing the new circuit board you will need to replace the old wall console with this new Series II wall console\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c!-- TABS --\u003e\n\u003ch5\u003eReviews\u003c\/h5\u003e\n\u003cp\u003e \u003c\/p\u003e\n\u003ch5\u003eInstallation Instructions\u003c\/h5\u003e\n\u003cp style=\"text-align: left;\"\u003e\u003ca href=\"https:\/\/cdn.shopify.com\/s\/files\/1\/1470\/8272\/files\/38875R3.S_Replacement_Board.pdf?4125\" target=\"_blank\" rel=\"noopener noreferrer\"\u003e\u003cimg alt=\"\" src=\"\/\/cdn.shopify.com\/s\/files\/1\/1470\/8272\/files\/PDF_ICON_icon.png?v=1533737947\" style=\"float: none;\"\u003e PDF Instructions for replacing the 38875R3.S circuit board \u003c\/a\u003e\u003c\/p\u003e\n\u003cp style=\"text-align: left;\"\u003e\u003ca href=\"https:\/\/cdn.shopify.com\/s\/files\/1\/1470\/8272\/files\/Programming_Travel_Limits_when_replacing_the_circuit_board.pdf?4125\" target=\"_blank\" rel=\"noopener noreferrer\"\u003e\u003cimg alt=\"\" src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/1470\/8272\/files\/PDF_ICON_icon.png?v=1533737947\"\u003e PDF Instructions for resetting the travel Limits after replacing the circuit board \u003c\/a\u003e\u003c\/p\u003e\n\u003cp style=\"text-align: left;\"\u003e\u003ca href=\"https:\/\/www.geniecompany.com\/data\/products\/accessories\/wall-console-series-II_ENG-FRE_02-01-2015.pdf\" target=\"_blank\" rel=\"noopener noreferrer\"\u003e\u003cimg alt=\"\" src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/1470\/8272\/files\/PDF_ICON_icon.png?v=1533737947\"\u003e PDF Instructions for replacing the Series II wall console\u003c\/a\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003e38875R3.S DC Control Board Replacement \u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eThese instructions are written assuming that you will have ample room around Opener to perform this repair. Some rare instances will require removal of the unit from its mounting hardware and repair made on a bench or floor. Refer to your \u003ca href=\"https:\/\/www.geniecompany.com\/data\/products\/genie_owners-manual_eng.pdf\" target=\"_blank\" rel=\"noopener noreferrer\"\u003eOwner’s Manual\u003c\/a\u003e for proper assembly and carefully read and understand all warnings and cautions pertaining to your unit.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eWARNING!\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eBE SURE ELECTRICAL POWER HAS BEEN DISCONNECTED FROM THE INPUT POWER LINES PRIOR TO REMOVING THE MOTOR COVER.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eWARNING!\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eANY AND ALL REPAIRS MADE TO THIS UNIT MUST BE PERFORMED WITH THE DOOR DISCONNECTED FROM THE OPENER AND IN THE CLOSED POSITION.\u003c\/p\u003e\n\u003cp\u003e1. Pull emergency release cord on carriage to disengage opener to close door if necessary. (If unable to lower door using opener, use extreme caution manually closing door. Before pulling emergency release cord, make certain people and objects are clear of door opening.)\u003c\/p\u003e\n\u003cp\u003e2. Unplug the garage door opener power cord from the power outlet.\u003c\/p\u003e\n\u003cp\u003e3. Open the garage door opener lens cover by inward on the middle tab. Once the lens cover is open remove light bulbs. Shown in FIG. 1.\u003c\/p\u003e\n\u003cp style=\"text-align: left;\"\u003e\u003cimg alt=\"Circuit Board Replacement 38875R3.S figure 1\" src=\"\/\/cdn.shopify.com\/s\/files\/1\/1470\/8272\/files\/38875R3.S_Replacement_Circuit_Board_Fig.1_large.png?v=1558617185\" style=\"float: none;\"\u003e\u003c\/p\u003e\n\u003cp\u003e4. Remove the wall console and Safe-T-Beam wires from the terminal block that is located on side of garage door opener power head. Shown in FIG. 1. Use small common screwdriver to press in on the orange tabs while gently pulling the wall console and safety beam wires from the terminal block. Mark these wires when removing to help facilitate replacement.\u003c\/p\u003e\n\u003cp\u003e5. Unplug any optional accessories that are installed such as the garage door opener battery backup and\/or the networking adapter.\u003c\/p\u003e\n\u003cp\u003e6. Remove two 5\/16” screws securing powerhead cover to chassis. FIG. 2.\u003c\/p\u003e\n\u003cp\u003e\u003cimg src=\"\/\/cdn.shopify.com\/s\/files\/1\/1470\/8272\/files\/38875R3.S_Replacement_Circuit_Board_Fig.2_large.png?v=1558617231\" alt=\"Genie Circuit board replacement figure 2\"\u003e\u003c\/p\u003e\n\u003cp\u003e7. Allow the motor cover to swing down to access control board and wire harnesses.\u003c\/p\u003e\n\u003cp\u003e8. Unplug the following harnesses from the control board. FIG. 4.\u003c\/p\u003e\n\u003cp\u003e• Light harness\u003c\/p\u003e\n\u003cp\u003e• Motor harness\u003c\/p\u003e\n\u003cp\u003e• Opto harness (see step 12-13)\u003c\/p\u003e\n\u003cp\u003e• AC IN harness\u003c\/p\u003e\n\u003cp\u003e• Motion Detector harness (if equipped)\u003c\/p\u003e\n\u003cp\u003e• Green ground wire to chassis (if equipped).\u003c\/p\u003e\n\u003cp\u003eREMOVE AND DISCARD.\u003c\/p\u003e\n\u003cp\u003e\u003cimg src=\"\/\/cdn.shopify.com\/s\/files\/1\/1470\/8272\/files\/38875R3.S_Replacement_Circuit_Board_Fig.3_large.png?v=1558617270\" alt=\"Genie Circuit board replacement figure 3\"\u003e \u003cimg src=\"\/\/cdn.shopify.com\/s\/files\/1\/1470\/8272\/files\/38875R3.S_Replacement_Circuit_Board_Fig.4_large.png?v=1558617299\" alt=\"Genie Circuit board replacement figure 4\"\u003e\u003c\/p\u003e\n\u003cp\u003e9. Powerhead cover can now be removed from opener chassis for repair. Special care should be taken to prevent damage to motion detector bulb located on the bottom of motor cover. (If equipped).\u003c\/p\u003e\n\u003cp\u003e10. Remove control board mounting screws and the old circuit board. Shown in FIG 3.\u003c\/p\u003e\n\u003cp\u003e11. Feed the antenna wire through the hole in the cover. Mount the replacement 38875R3.S circuit board to cover and secure with old screws removed in step 10.\u003c\/p\u003e\n\u003cp\u003e--- SEE BELOW FOR MOTOR TYPES ---\u003c\/p\u003e\n\u003cp\u003e12. If your motor compares to MOTOR TYPE 1. Remove existing harness from motor and plug pre-installed OPTO SENSOR harness from new control board directly into motor.\u003c\/p\u003e\n\u003cp\u003e13. If your motor compares to MOTOR TYPE 2. Remove pre-installed OPTO SENSOR harness from control board and plug existing OPTO harness from motor into DUAL ENCODER OPTO SENSOR plug on replacement control board. (Or use new harness packed with control board).\u003c\/p\u003e\n\u003cp\u003e14. Hang powerhead cover to chassis to connect all other harnesses removed in step 8.\u003c\/p\u003e\n\u003cp\u003e15. Swing powerhead cover up onto chassis and secure using screws removed in step 6.\u003c\/p\u003e\n\u003cp\u003e16. Install wall control and Safe-T-Beam wires. Install battery backup and\/or network harnesses if applicable.\u003c\/p\u003e\n\u003cp\u003e17. Install light bulbs and close lens cover.\u003c\/p\u003e\n\u003cp\u003e18. Reapply power to opener.\u003c\/p\u003e\n\u003cp\u003e19. Limit controls, transmitters and full function test will be required. Refer to the \u003ca href=\"https:\/\/www.geniecompany.com\/data\/products\/genie_owners-manual_eng.pdf\" target=\"_blank\" rel=\"noopener noreferrer\"\u003eowner’s manual\u003c\/a\u003e and\/or assembly poster for detailed information  \u003c\/p\u003e\n\u003cp\u003e20. See below to replace the wall console \u003c\/p\u003e\n\u003cp style=\"text-align: left;\"\u003e\u003cimg alt=\"Genie motor type images for replacement circuit boards \" src=\"\/\/cdn.shopify.com\/s\/files\/1\/1470\/8272\/files\/38875R3.S_Replacement_Circuit_Board_Motor_Types_Figure_grande.png?v=1558617333\" style=\"float: none;\"\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eINSTALLING REPLACEMENT SERIES II WALL CONSOLE\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e• Disconnect power to the powerhead.\u003c\/p\u003e\n\u003cp\u003e• Remove existing wall console from the wall by removing mounting screws.• Remove wires from existing wall console.\u003c\/p\u003e\n\u003cp\u003e• Split and strip ends of the wire if it is needed (Fig. 2).\u003c\/p\u003e\n\u003cp\u003e\u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/1470\/8272\/files\/wc_fig_2_medium.png?v=1548876120\" alt=\"\"\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003e• \u003c\/strong\u003eFasten the wire to control board screws on the back of the wall console (Fig. 3):\u003c\/p\u003e\n\u003cp\u003e \u003c\/p\u003e\n\u003cp\u003e\u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/1470\/8272\/files\/wc_fig_3_medium.png?v=1548876180\" alt=\"\"\u003e \u003c\/p\u003e\n\u003cp\u003e \u003cimg src=\"\/\/cdn.shopify.com\/s\/files\/1\/1470\/8272\/files\/wc_fig_7_large.png?v=1548876688\" alt=\"\"\u003e\u003c\/p\u003e\n\u003cp\u003e• Connect white wire between powerhead terminal #3 to wall console terminal “W.” (Fig 3 \u0026amp; 7).\u003c\/p\u003e\n\u003cp\u003e• Connect striped wire between powerhead terminal #4 to wall console terminal “B.” (Fig 3 \u0026amp; 7).\u003c\/p\u003e\n\u003cp\u003eNOTE: When existing wires have a color code different from above (FIG. 3), or none at all—make sure the wires are connected between terminals as directed above. When the wires are connected to the opposite terminals, the Sure-Lock® and Light feature may not function. The first indication of incorrect wiring is the backlight will be OFF.\u003c\/p\u003e\n\u003cp\u003e\u003cspan\u003e• \u003c\/span\u003eMount wall console to wall using screws provided. Verify height at least 5 ft. above the floor (Fig. 4).\u003c\/p\u003e\n\u003cp\u003eReconnect power to the powerhead.\u003c\/p\u003e\n\u003cp\u003e• Check operation of each wall console button and feature (If the circuit board was replaced, and then the wall console, reset the limits on the garage door opener before checking the wall console features.) \u003c\/p\u003e\n\u003cp\u003e\u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/1470\/8272\/files\/wc_fig_4_medium.png?v=1548876302\" alt=\"\"\u003e\u003c\/p\u003e\n\u003c!-- \/TABS --\u003e","published_at":"2017-06-26T16:22:41-04:00","created_at":"2017-06-26T16:24:09-04:00","vendor":"The Genie Company","type":"Service Parts","tags":["Circuit Board"],"price":14029,"price_min":14029,"price_max":14029,"available":true,"price_varies":false,"compare_at_price":null,"compare_at_price_min":0,"compare_at_price_max":0,"compare_at_price_varies":false,"variants":[{"id":41470750083,"title":"Default Title","option1":"Default Title","option2":null,"option3":null,"sku":"38875R3.S","requires_shipping":true,"taxable":true,"featured_image":null,"available":true,"name":"Circuit Board \/ Series II Wall Console Bundle 38875R3.S","public_title":null,"options":["Default Title"],"price":14029,"weight":635,"compare_at_price":null,"inventory_quantity":999,"inventory_management":"shopify","inventory_policy":"continue","barcode":""}],"images":["\/\/cdn.shopify.com\/s\/files\/1\/1470\/8272\/products\/38875R3.S-Board-F.jpg?v=1555442416","\/\/cdn.shopify.com\/s\/files\/1\/1470\/8272\/products\/38875R3.S-Board-T.jpg?v=1555442447"],"featured_image":"\/\/cdn.shopify.com\/s\/files\/1\/1470\/8272\/products\/38875R3.S-Board-F.jpg?v=1555442416","options":["Title"],"content":"\u003cp\u003e\u003cspan\u003eThis replacement circuit board with series II wall console is for certain Genie chain or belt drive models. Once you have determined your circuit board needs to be replaced\u003c\/span\u003e\u003cspan\u003e this board\/ wall console bundle will get your garage door opener back up and running quickly. \u003c\/span\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eCompatible with models 3022, 3024, 3042 (ChainMax 1000, SilentMax 1000, IntelliG 1000)\u003c\/li\u003e\n\u003cli\u003eReplaces old circuit board numbers - 38334R3.S, 38001R3.S\u003c\/li\u003e\n\u003cli\u003eGenuine Genie replacement parts\u003c\/li\u003e\n\u003cli\u003eRequires re-programming of limits and accessories with the new board \u003c\/li\u003e\n\u003cli\u003eAll remotes, keypads or wireless devices that you currently use will work with the new circuit board (after reprogramming)\u003c\/li\u003e\n\u003cli\u003eBundle Kit includes the replacement instructions, circuit board, and series II wall console  \u003c\/li\u003e\n\u003cli\u003eIf you had a Series III wall console (Gray with black buttons), when installing the new circuit board you will need to replace the old wall console with this new Series II wall console\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c!-- TABS --\u003e\n\u003ch5\u003eReviews\u003c\/h5\u003e\n\u003cp\u003e \u003c\/p\u003e\n\u003ch5\u003eInstallation Instructions\u003c\/h5\u003e\n\u003cp style=\"text-align: left;\"\u003e\u003ca href=\"https:\/\/cdn.shopify.com\/s\/files\/1\/1470\/8272\/files\/38875R3.S_Replacement_Board.pdf?4125\" target=\"_blank\" rel=\"noopener noreferrer\"\u003e\u003cimg alt=\"\" src=\"\/\/cdn.shopify.com\/s\/files\/1\/1470\/8272\/files\/PDF_ICON_icon.png?v=1533737947\" style=\"float: none;\"\u003e PDF Instructions for replacing the 38875R3.S circuit board \u003c\/a\u003e\u003c\/p\u003e\n\u003cp style=\"text-align: left;\"\u003e\u003ca href=\"https:\/\/cdn.shopify.com\/s\/files\/1\/1470\/8272\/files\/Programming_Travel_Limits_when_replacing_the_circuit_board.pdf?4125\" target=\"_blank\" rel=\"noopener noreferrer\"\u003e\u003cimg alt=\"\" src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/1470\/8272\/files\/PDF_ICON_icon.png?v=1533737947\"\u003e PDF Instructions for resetting the travel Limits after replacing the circuit board \u003c\/a\u003e\u003c\/p\u003e\n\u003cp style=\"text-align: left;\"\u003e\u003ca href=\"https:\/\/www.geniecompany.com\/data\/products\/accessories\/wall-console-series-II_ENG-FRE_02-01-2015.pdf\" target=\"_blank\" rel=\"noopener noreferrer\"\u003e\u003cimg alt=\"\" src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/1470\/8272\/files\/PDF_ICON_icon.png?v=1533737947\"\u003e PDF Instructions for replacing the Series II wall console\u003c\/a\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003e38875R3.S DC Control Board Replacement \u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eThese instructions are written assuming that you will have ample room around Opener to perform this repair. Some rare instances will require removal of the unit from its mounting hardware and repair made on a bench or floor. Refer to your \u003ca href=\"https:\/\/www.geniecompany.com\/data\/products\/genie_owners-manual_eng.pdf\" target=\"_blank\" rel=\"noopener noreferrer\"\u003eOwner’s Manual\u003c\/a\u003e for proper assembly and carefully read and understand all warnings and cautions pertaining to your unit.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eWARNING!\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eBE SURE ELECTRICAL POWER HAS BEEN DISCONNECTED FROM THE INPUT POWER LINES PRIOR TO REMOVING THE MOTOR COVER.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eWARNING!\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eANY AND ALL REPAIRS MADE TO THIS UNIT MUST BE PERFORMED WITH THE DOOR DISCONNECTED FROM THE OPENER AND IN THE CLOSED POSITION.\u003c\/p\u003e\n\u003cp\u003e1. Pull emergency release cord on carriage to disengage opener to close door if necessary. (If unable to lower door using opener, use extreme caution manually closing door. Before pulling emergency release cord, make certain people and objects are clear of door opening.)\u003c\/p\u003e\n\u003cp\u003e2. Unplug the garage door opener power cord from the power outlet.\u003c\/p\u003e\n\u003cp\u003e3. Open the garage door opener lens cover by inward on the middle tab. Once the lens cover is open remove light bulbs. Shown in FIG. 1.\u003c\/p\u003e\n\u003cp style=\"text-align: left;\"\u003e\u003cimg alt=\"Circuit Board Replacement 38875R3.S figure 1\" src=\"\/\/cdn.shopify.com\/s\/files\/1\/1470\/8272\/files\/38875R3.S_Replacement_Circuit_Board_Fig.1_large.png?v=1558617185\" style=\"float: none;\"\u003e\u003c\/p\u003e\n\u003cp\u003e4. Remove the wall console and Safe-T-Beam wires from the terminal block that is located on side of garage door opener power head. Shown in FIG. 1. Use small common screwdriver to press in on the orange tabs while gently pulling the wall console and safety beam wires from the terminal block. Mark these wires when removing to help facilitate replacement.\u003c\/p\u003e\n\u003cp\u003e5. Unplug any optional accessories that are installed such as the garage door opener battery backup and\/or the networking adapter.\u003c\/p\u003e\n\u003cp\u003e6. Remove two 5\/16” screws securing powerhead cover to chassis. FIG. 2.\u003c\/p\u003e\n\u003cp\u003e\u003cimg src=\"\/\/cdn.shopify.com\/s\/files\/1\/1470\/8272\/files\/38875R3.S_Replacement_Circuit_Board_Fig.2_large.png?v=1558617231\" alt=\"Genie Circuit board replacement figure 2\"\u003e\u003c\/p\u003e\n\u003cp\u003e7. Allow the motor cover to swing down to access control board and wire harnesses.\u003c\/p\u003e\n\u003cp\u003e8. Unplug the following harnesses from the control board. FIG. 4.\u003c\/p\u003e\n\u003cp\u003e• Light harness\u003c\/p\u003e\n\u003cp\u003e• Motor harness\u003c\/p\u003e\n\u003cp\u003e• Opto harness (see step 12-13)\u003c\/p\u003e\n\u003cp\u003e• AC IN harness\u003c\/p\u003e\n\u003cp\u003e• Motion Detector harness (if equipped)\u003c\/p\u003e\n\u003cp\u003e• Green ground wire to chassis (if equipped).\u003c\/p\u003e\n\u003cp\u003eREMOVE AND DISCARD.\u003c\/p\u003e\n\u003cp\u003e\u003cimg src=\"\/\/cdn.shopify.com\/s\/files\/1\/1470\/8272\/files\/38875R3.S_Replacement_Circuit_Board_Fig.3_large.png?v=1558617270\" alt=\"Genie Circuit board replacement figure 3\"\u003e \u003cimg src=\"\/\/cdn.shopify.com\/s\/files\/1\/1470\/8272\/files\/38875R3.S_Replacement_Circuit_Board_Fig.4_large.png?v=1558617299\" alt=\"Genie Circuit board replacement figure 4\"\u003e\u003c\/p\u003e\n\u003cp\u003e9. Powerhead cover can now be removed from opener chassis for repair. Special care should be taken to prevent damage to motion detector bulb located on the bottom of motor cover. (If equipped).\u003c\/p\u003e\n\u003cp\u003e10. Remove control board mounting screws and the old circuit board. Shown in FIG 3.\u003c\/p\u003e\n\u003cp\u003e11. Feed the antenna wire through the hole in the cover. Mount the replacement 38875R3.S circuit board to cover and secure with old screws removed in step 10.\u003c\/p\u003e\n\u003cp\u003e--- SEE BELOW FOR MOTOR TYPES ---\u003c\/p\u003e\n\u003cp\u003e12. If your motor compares to MOTOR TYPE 1. Remove existing harness from motor and plug pre-installed OPTO SENSOR harness from new control board directly into motor.\u003c\/p\u003e\n\u003cp\u003e13. If your motor compares to MOTOR TYPE 2. Remove pre-installed OPTO SENSOR harness from control board and plug existing OPTO harness from motor into DUAL ENCODER OPTO SENSOR plug on replacement control board. (Or use new harness packed with control board).\u003c\/p\u003e\n\u003cp\u003e14. Hang powerhead cover to chassis to connect all other harnesses removed in step 8.\u003c\/p\u003e\n\u003cp\u003e15. Swing powerhead cover up onto chassis and secure using screws removed in step 6.\u003c\/p\u003e\n\u003cp\u003e16. Install wall control and Safe-T-Beam wires. Install battery backup and\/or network harnesses if applicable.\u003c\/p\u003e\n\u003cp\u003e17. Install light bulbs and close lens cover.\u003c\/p\u003e\n\u003cp\u003e18. Reapply power to opener.\u003c\/p\u003e\n\u003cp\u003e19. Limit controls, transmitters and full function test will be required. Refer to the \u003ca href=\"https:\/\/www.geniecompany.com\/data\/products\/genie_owners-manual_eng.pdf\" target=\"_blank\" rel=\"noopener noreferrer\"\u003eowner’s manual\u003c\/a\u003e and\/or assembly poster for detailed information  \u003c\/p\u003e\n\u003cp\u003e20. See below to replace the wall console \u003c\/p\u003e\n\u003cp style=\"text-align: left;\"\u003e\u003cimg alt=\"Genie motor type images for replacement circuit boards \" src=\"\/\/cdn.shopify.com\/s\/files\/1\/1470\/8272\/files\/38875R3.S_Replacement_Circuit_Board_Motor_Types_Figure_grande.png?v=1558617333\" style=\"float: none;\"\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eINSTALLING REPLACEMENT SERIES II WALL CONSOLE\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e• Disconnect power to the powerhead.\u003c\/p\u003e\n\u003cp\u003e• Remove existing wall console from the wall by removing mounting screws.• Remove wires from existing wall console.\u003c\/p\u003e\n\u003cp\u003e• Split and strip ends of the wire if it is needed (Fig. 2).\u003c\/p\u003e\n\u003cp\u003e\u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/1470\/8272\/files\/wc_fig_2_medium.png?v=1548876120\" alt=\"\"\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003e• \u003c\/strong\u003eFasten the wire to control board screws on the back of the wall console (Fig. 3):\u003c\/p\u003e\n\u003cp\u003e \u003c\/p\u003e\n\u003cp\u003e\u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/1470\/8272\/files\/wc_fig_3_medium.png?v=1548876180\" alt=\"\"\u003e \u003c\/p\u003e\n\u003cp\u003e \u003cimg src=\"\/\/cdn.shopify.com\/s\/files\/1\/1470\/8272\/files\/wc_fig_7_large.png?v=1548876688\" alt=\"\"\u003e\u003c\/p\u003e\n\u003cp\u003e• Connect white wire between powerhead terminal #3 to wall console terminal “W.” (Fig 3 \u0026amp; 7).\u003c\/p\u003e\n\u003cp\u003e• Connect striped wire between powerhead terminal #4 to wall console terminal “B.” (Fig 3 \u0026amp; 7).\u003c\/p\u003e\n\u003cp\u003eNOTE: When existing wires have a color code different from above (FIG. 3), or none at all—make sure the wires are connected between terminals as directed above. When the wires are connected to the opposite terminals, the Sure-Lock® and Light feature may not function. The first indication of incorrect wiring is the backlight will be OFF.\u003c\/p\u003e\n\u003cp\u003e\u003cspan\u003e• \u003c\/span\u003eMount wall console to wall using screws provided. Verify height at least 5 ft. above the floor (Fig. 4).\u003c\/p\u003e\n\u003cp\u003eReconnect power to the powerhead.\u003c\/p\u003e\n\u003cp\u003e• Check operation of each wall console button and feature (If the circuit board was replaced, and then the wall console, reset the limits on the garage door opener before checking the wall console features.) \u003c\/p\u003e\n\u003cp\u003e\u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/1470\/8272\/files\/wc_fig_4_medium.png?v=1548876302\" alt=\"\"\u003e\u003c\/p\u003e\n\u003c!-- \/TABS --\u003e"}

Circuit Board / Series II Wall Console Bundle 38875R3.S

Product Description
$140.29
Maximum quantity available reached.

This replacement circuit board with series II wall console is for certain Genie chain or belt drive models. Once you have determined your circuit board needs to be replaced this board/ wall console bundle will get your garage door opener back up and running quickly. 

  • Compatible with models 3022, 3024, 3042 (ChainMax 1000, SilentMax 1000, IntelliG 1000)
  • Replaces old circuit board numbers - 38334R3.S, 38001R3.S
  • Genuine Genie replacement parts
  • Requires re-programming of limits and accessories with the new board 
  • All remotes, keypads or wireless devices that you currently use will work with the new circuit board (after reprogramming)
  • Bundle Kit includes the replacement instructions, circuit board, and series II wall console  
  • If you had a Series III wall console (Gray with black buttons), when installing the new circuit board you will need to replace the old wall console with this new Series II wall console
Sku: 38875R3.S

 PDF Instructions for replacing the 38875R3.S circuit board 

 PDF Instructions for resetting the travel Limits after replacing the circuit board 

 PDF Instructions for replacing the Series II wall console

38875R3.S DC Control Board Replacement

These instructions are written assuming that you will have ample room around Opener to perform this repair. Some rare instances will require removal of the unit from its mounting hardware and repair made on a bench or floor. Refer to your Owner’s Manual for proper assembly and carefully read and understand all warnings and cautions pertaining to your unit.

WARNING!

BE SURE ELECTRICAL POWER HAS BEEN DISCONNECTED FROM THE INPUT POWER LINES PRIOR TO REMOVING THE MOTOR COVER.

WARNING!

ANY AND ALL REPAIRS MADE TO THIS UNIT MUST BE PERFORMED WITH THE DOOR DISCONNECTED FROM THE OPENER AND IN THE CLOSED POSITION.

1. Pull emergency release cord on carriage to disengage opener to close door if necessary. (If unable to lower door using opener, use extreme caution manually closing door. Before pulling emergency release cord, make certain people and objects are clear of door opening.)

2. Unplug the garage door opener power cord from the power outlet.

3. Open the garage door opener lens cover by inward on the middle tab. Once the lens cover is open remove light bulbs. Shown in FIG. 1.

Circuit Board Replacement 38875R3.S figure 1

4. Remove the wall console and Safe-T-Beam wires from the terminal block that is located on side of garage door opener power head. Shown in FIG. 1. Use small common screwdriver to press in on the orange tabs while gently pulling the wall console and safety beam wires from the terminal block. Mark these wires when removing to help facilitate replacement.

5. Unplug any optional accessories that are installed such as the garage door opener battery backup and/or the networking adapter.

6. Remove two 5/16” screws securing powerhead cover to chassis. FIG. 2.

Genie Circuit board replacement figure 2

7. Allow the motor cover to swing down to access control board and wire harnesses.

8. Unplug the following harnesses from the control board. FIG. 4.

• Light harness

• Motor harness

• Opto harness (see step 12-13)

• AC IN harness

• Motion Detector harness (if equipped)

• Green ground wire to chassis (if equipped).

REMOVE AND DISCARD.

Genie Circuit board replacement figure 3 Genie Circuit board replacement figure 4

9. Powerhead cover can now be removed from opener chassis for repair. Special care should be taken to prevent damage to motion detector bulb located on the bottom of motor cover. (If equipped).

10. Remove control board mounting screws and the old circuit board. Shown in FIG 3.

11. Feed the antenna wire through the hole in the cover. Mount the replacement 38875R3.S circuit board to cover and secure with old screws removed in step 10.

--- SEE BELOW FOR MOTOR TYPES ---

12. If your motor compares to MOTOR TYPE 1. Remove existing harness from motor and plug pre-installed OPTO SENSOR harness from new control board directly into motor.

13. If your motor compares to MOTOR TYPE 2. Remove pre-installed OPTO SENSOR harness from control board and plug existing OPTO harness from motor into DUAL ENCODER OPTO SENSOR plug on replacement control board. (Or use new harness packed with control board).

14. Hang powerhead cover to chassis to connect all other harnesses removed in step 8.

15. Swing powerhead cover up onto chassis and secure using screws removed in step 6.

16. Install wall control and Safe-T-Beam wires. Install battery backup and/or network harnesses if applicable.

17. Install light bulbs and close lens cover.

18. Reapply power to opener.

19. Limit controls, transmitters and full function test will be required. Refer to the owner’s manual and/or assembly poster for detailed information  

20. See below to replace the wall console 

Genie motor type images for replacement circuit boards

INSTALLING REPLACEMENT SERIES II WALL CONSOLE

• Disconnect power to the powerhead.

• Remove existing wall console from the wall by removing mounting screws.• Remove wires from existing wall console.

• Split and strip ends of the wire if it is needed (Fig. 2).

• Fasten the wire to control board screws on the back of the wall console (Fig. 3):

 

 

 

• Connect white wire between powerhead terminal #3 to wall console terminal “W.” (Fig 3 & 7).

• Connect striped wire between powerhead terminal #4 to wall console terminal “B.” (Fig 3 & 7).

NOTE: When existing wires have a color code different from above (FIG. 3), or none at all—make sure the wires are connected between terminals as directed above. When the wires are connected to the opposite terminals, the Sure-Lock® and Light feature may not function. The first indication of incorrect wiring is the backlight will be OFF.

• Mount wall console to wall using screws provided. Verify height at least 5 ft. above the floor (Fig. 4).

Reconnect power to the powerhead.

• Check operation of each wall console button and feature (If the circuit board was replaced, and then the wall console, reset the limits on the garage door opener before checking the wall console features.) 

Questions & Answers

Ask a Question
  • Does G3T remote work with this circuit board ?

    Yes, it does. 

  • Does this come with instructions how to remove and replace the board??? I opened teh cover but it looks like I have to get on a ladder and unscrew the actual unit inder the cover near the bulbs.... PLEASE email me instructions if not.... thx!

    This does come with instructions on how to change the board. If you need assistance you can also contact our customer service at 1-800-354-3643 and we can walk you through the steps.