Skip to product information
1 of 1

The Genie Company

Motor (600 Series) - 36447A.S

Motor (600 Series) - 36447A.S

Regular price $178.86 USD
Regular price Sale price $178.86 USD
Sale Sold out

Product has been discontinued and is NO LONGER AVAILABLE.

Garage door opener motor replacement for the Genie 600 series operator. Compatible models listed below. 

  • Compatible with models: 1022, 1024, 1042 (Chainlift 600, BeltLift 600) 
  • DC, G-SM01

SKU: 36447A.S

Sorry, this product is currently out of stock.

ASK A QUESTION View full details
Motor (600 Series) - 36447A.S
Motor (600 Series) - 36447A.S
$178.86

QUESTIONS & ANSWERS

Ask a Question
  • My model 1022 1/2 hp

    Yes, the Motor (600 Series) - 36447A.S is compatible with the model 1022.

  • I have a 1024 and the opener worked for approximately one minute and then is unresponsive. Pulled it apart, put it back together and same thing- worked for a minute then stopped. Getting three blinking green light. I have tried everything - any thoughts?

    You can view some troubleshooting tips for the 1024 model garage door opener here. If you are getting 3 blinks, that normally means the limits are set backward. You would want to clear and reset the limits shown here in the owner's manual in section 6. 

  • Will I have to remove the chain and sprocket in order to get to the bolts that hold the motor in place?

    Yes, you would have to remove the rail from the powerhead.

  • what is the horsepower of this unit, and how much weight can it handle?

    This was on a 1/2 HP garage door opener. Rated for a 500lb door.

  • The drive motor is beginning to struggle with lifting the double door, even with increasing the force, is there a direct replacement part for the discontinued 36447A Motor Assembly for the Model 1024? I would appreciate any assistance that you can provide. v/r Ronald

    Unfortunately, this part is obsolete so we do not have a replacement part. We apologize for the inconvenience.

PDF Installation instructions for 36447A.S Motor Replacement 

36447A.S Motor Replacement Instructions

This repair will require removal of the unit from it’s mounting hardware and repair made on a clean work surface. Refer to your owners manual to reverse the wiring, mounting, and assembly process. READ AND FOLLOW ALL SAFETY, INSTALLATION AND OPERATION INSTRUCTIONS AND WARNINGS CONTAINED IN THESE INSTRUCTIONS AND THE OWNERS MANUAL. If you have any questions or do not understand an instruction, contact a trained service technician. Or call 800-354-3643.

WARNING
BE SURE ELECTRICAL POWER HAS BEEN DISCONNECTED FROM THE INPUT POWER LINES PRIOR TO REMOVING THE MOTOR COVER.

WARNING
ANY AND ALL REPAIRS MADE TO THIS UNIT MUST BE PERFORMED WITH THE DOOR DISCONNECTED FROM THE OPENER AND IN THE CLOSED POSITION.

 

 1. Before pulling emergency release cord, make certain people and objects are clear of door opening. Pull emergency release cord on carriage to disengage opener to close door if necessary. (If unable to lower door using opener, use extreme caution manually closing door.

2. Remove power from opener.

3. Remove lens cover(s) by pressing side tabs inward and remove light bulb(s). FIG. 1.

Genie 600/800 Series motor replacement instructions firgure 1

4. Remove wall control and Safe-T-Beam® wires from terminal block located on back of opener FIG. 1. Use small common screwdriver to press in on orange locking clips while gently pulling wires from block. Mark wires to help facilitate replacement.

5. Remove door arm clevis pin and cotter-hairpin to disconnect operator from door. FIG. 2.

Genie 600/800 Motor replacement instructions figure 2

6. Remove opener from mounting brackets and hardware and set on a clean work surface.

7. Remove 3 bolts from rail assembly and set rail aside. FIG. 1.

8. Remove 2 screws securing control board to powerhead cover. FIG. 3.

Genie Motor replacement for 600/800 series instructions figure 3

Genie Motor replacement 36447A.S figure 4

9. Lower the control board assembly to access control board and wire harnesses.

10. Note locations and unplug wire harnesses from control board. FIG. 5.
• OPTO, LIGHTS, MOTOR, TRANSFORMER HARNESSES

Genie 36447A.S Motor replacement instructions figure 5

11. Remove 4 screws securing cover and remove cover. FIG. 6.

Genie 36447A.S Motor replacement instructions figure 6

12. Remove 3 screws at top of powerhead to remove motor. FIG. 7.

Genie 36447A.S Motor replacement instructions figure 7

13. Install replacement 36447A.S motor in reverse order.

14. Replace cover with 4 screws.

15. Replace control board harnesses.

Note: Be certain to install all harnesses in the correct position.

16. Replace control board assembly and secure with 2 screws.

17. Install rail assembly to powerhead with 3 bolts.

18. Reinstall powerhead and rail assembly to ceiling and door. Steps 5,4,3.

19. Install light bulb(s) and lens cover(s).

20. Apply power to opener.

21. Test unit fully to ensure travel limits, remote controls and all safety features work correctly. Refer to your owners manual and/or assembly poster.

  • Shipping Truck

    Free Shipping

    We offer FREE shipping and handling on all orders that total over $17.99 and are shipped to a US address. All orders are shipped using UPS ground, directly from The Genie Company.

  • Genuine Genie Accessories and Parts

    Genuine Replacements

    Buying GENUINE Genie accessories and parts guarantees that you are getting quality OEM materials backed by a Genie warranty.

  • Customer support chat

    Support

    Need assistance? We are here for you! We offer a wide range of customer support options including contact by phone or email, web chat services with a live agent, and a robust support section also located on our website.  All customer care teams and services are based in the USA.

FREE SHIPPING ON ALL US ORDERS 17.99 AND UP