Skip to product information
1 of 3

The Genie Company

Wall Console for Series III Product

Wall Console for Series III Product

Regular price $27.99 USD
Regular price Sale price $27.99 USD
Sale Sold out

Multi-function wired wall console with open/close, light and vacation lock buttons. There is a red led light in the wall console that lights up to help locate the wall console in the dark. 

  • ONLY compatible with Models 3022, 3024, 3042, 4022, 4024, 4042, 3062, 3064, 4062, 4064 that have a serial number LOWER than the number 122494110518
  • Circuit board inside the operator must start with the '37470R' prefix
  • Use this Series III wall console to directly add to or replace another Series III wall console of the exact same design and coloring 

 

 California Residents: Proposition 65 WARNING

SKU: 37222R

In Stock! Usually ships within 24 hours.

ASK A QUESTION View full details
Genie Series III Garage Door Opener Wall Console_37222R
Wall Console for Series III Product
$27.99

QUESTIONS & ANSWERS

Ask a Question
  • Which wall console works with the IntellaG 1000? My wall console is only working some of the time but my remotes work all the time so I think there must be an issue with the wall console.

    For the IntelliG 1000 if you have a gray console with white/translucent buttons you would need wall console 39165R. If you have a grey console with black buttons you would need wall console 37222R.

  • will this work with GPS1200IC?

    No, the Genie model GPS1200IC requires the Wall Console for Series II Product - 39165R.

  • My series III wall console stopped working (remote operates door as normal). Opener and wall console are approximately 8 years old. The 3 buttons on the wall console have no effect. The red LED on the wall console is on, I measured approximately 12VDC on the 2-wire connection to the wall console. If I can measure the signal from the wall console, I can see if the problem is the wall console itself or at the opener. Can you tell me if the signal from the wall console is simply a DC current signal, or something else I can measure with a multimeter? I assume the wall console sinks different mADC current levels to trigger the opener's functions, but I don't know if there is more to it than that. Thank you!

    It’s DC current and should run 12-20 volts.  If the remotes operate the door normally, the issue would most likely be the wall console or wiring, You can remove the wall console and check the voltage if it is within that range the wall console should be replaced, if not the wiring should be replaced. 

  • Will it work with Genie Intellicode Screw Drive, 1/2 HP Model IS550/A, Receiver Model/Module ACSR3G?

    No, it will not. The IS550/A model garage door opener would use the Series II wall console.

  • will sku 37222R wall console work w/genie 900 model 2562

    The 37222R Series III wall console will work with the 2562 model as long as you currently have a series III wall console working. IF- the 2562 model is currently using the Series II wall console 39165R  (it would have white buttons), then you would need to keep with the Series II.

  • H8000-07 is there any wall mount opener that can be used to replace the old one?

    For the H8000-07 model garage door opener you would need the Series II wall console 39165R.

  • Which wall control replacement is compatible with Genie model H8000D?

    You can use the two Series II wall consoles. 39165R.

  • Will this work with model CM8600IC/M, and if not, is there a 3 button wall console I can use?

    This one will not. You would need the Series II wall console, 39165R.

  • Will this work with the 3060L series opener? The light will not shut off automatic.

    No, this will not work with the 3060L model. You would need the Series II wall console, 39165R. If you would like to troubleshoot the lights not turning off before purchasing a wall console, please contact Genie customer service at 1-800-354-3643 for assistance.

  • Will this work with genie intelligence G 1000 model # 3020

    This will work with the IntelliG 1000 if you already had the Series III wall console and have not replaced the circuit board. If you are not sure, please contact Genie customer service at 1-800-354-3643 for assistance.

  • Can you tell which wall unit I purchase for model number PMX500IC/B Genie pro max

    You would need the Genie series II wall console to use with your Genie model PMX500IC/B garage door opener.

  • Which wall console works with PowerLift 900

    For a Genie PowerLift 900 model, if your wall button is gray with white/backlit red you will need the Wall Console for Series II Product- 39165R.  If you have a wall button that is gray with black buttons you will need

PDF Series III Wall Console Installation Instructions 

Series III Replacement Wall Console, 37222R Installation 

1. IMPORTANT INFORMATION

Use only the Series III wall console with Genie® garage door
openers models 2562, 2564, 3022, 3024, 3042, 3062, 3064, 4022,
4024, 4042, 4062, and 4064 that were from 2010 through 2012 with Series III electronics. The serial number will be lower than 122494110518.  If you currently have a series III wall console and have not replaced the circuit board, this will work. If you are unsure, please contact Genie customer service at 1-800-354-3643. 

SERIES III WALL CONSOLE - OPERATION AND FEATURES

Wall console has three buttons and one indicator light.

Genie Series III Wall Console 37222R

Indicator Light
Indicator light will display red when wall console is properly wired and Sure-Lock™ is OFF. When Sure-Lock™ is ON indicator light flashes.

Open/Close Button
Use this button to open or close garage door. When Sure- Lock™ is ON the Open/Close button will CLOSE door only. Note: Constant button pressure in the CLOSE mode will override error responses in the powerhead and close door.

Independent Light Console Button
Use this button to turn powerhead lights ON. Powerhead lighting will remain ON until this button is pressed again or a door action has been completed. Note: If opener has a Motion Detector, the sensor will keep powerhead lights ON as long as motion is detected.

Sure-Lock™ Button
When Sure-Lock™ is ON the powerhead cannot be activated by the wall console or a remote.
• Press and hold for 5 seconds (or until Indicator Light flashes) to activate Sure-Lock™.
• Press and release to turn Sure-Lock™ OFF.

WARNING

• Verify there is NO power to the opener before installing wall console and/or wall console wires.
• Use of any other wall console can cause the door to operate unexpectedly and the light not to work. Use only the included wall console.

CAUTION

• Staples which are too tight can cut or pinch wires. Cut or pinched wires can cause the wall console to stop working. When using the insulated staples, make sure you fasten them only as tightly as needed to hold the wire snugly.

Genie Series III Wall Console Tools Required for Installation

Series III Wall Console - Replacement

Use these instructions when replacing a Series III wall console.

1. Install Replacement Wall Console
• Disconnect power to powerhead.
• Remove wires from existing wall console.
• Split and strip ends of wire if required (Fig. 2).
• Fasten wire to control board screws on back of wall console (Fig. 3).
– Striped wire to the + (plus) terminal
– White wire to the - (minus) terminal
• Mount wall console to wall using screws provided.
• Reconnect power to powerhead.
• Check operation of each wall console button and feature.

Genie Series III Wall console replacement instructions

 

Series III Wall Console - Expansion

Use these instructions when you are expanding or adding to an existing Series III wall console.

1. Wall Console Wiring (in series or in parallel)
• Disconnect power to powerhead.
• Pick a convenient location for mounting new wall console
NOTE: Securely anchor wires to ceiling and wall using insulated staples (Fig. 5). Staples should be snug only.
• (in series) Run wire from new wall console to existing wall console (Fig. 7).
– Split and strip ends of wire (Fig. 2)
– Fasten wire to control board screws on back of existing wall console.
Striped wire to the + (plus) terminal
White wire to the - (minus) terminal
• (in parallel) Run wire from new wall console to powerhead (Fig. 8).

– Route wire through wire guide on powerhead (Fig. 6)
– Split and strip ends of wire (Fig. 2)
– Insert wire into terminal holes and lightly press in the locking clips above each terminal hole (Fig. 8)
– Confirm wire lock by lightly tugging on the wire. Wire should remain in the terminal hole.

2. Fasten wire to control board screws on back of new wall console (Fig. 3).
Striped wire to the + (plus) terminal
White wire to the - (minus) terminal

3. Reconnect power to powerhead.
• Check operation of each button and feature of both wall consoles.

37222R Genie Series III wall console installation, adding

  • Shipping Truck

    Free Shipping

    We offer FREE shipping and handling on all orders that total over $17.99 and are shipped to a US address. All orders are shipped using UPS ground, directly from The Genie Company.

  • Genuine Genie Accessories and Parts

    Genuine Replacements

    Buying GENUINE Genie accessories and parts guarantees that you are getting quality OEM materials backed by a Genie warranty.

  • Customer support chat

    Support

    Need assistance? We are here for you! We offer a wide range of customer support options including contact by phone or email, web chat services with a live agent, and a robust support section also located on our website.  All customer care teams and services are based in the USA.

FREE SHIPPING ON ALL US ORDERS 17.99 AND UP