GL2T-BX 2-Button LED Flashlight Remote (2 Pack)
PDF Programming Instruction Manual GL2T-BX Genie Flashlight Remote
LED Flashlight Remote Programming Instructions (GL2T-BX)
1- Put the Garage Door Opener into Programming/ Learn Code Mode
Placing the garage door opener into programming/ learn code mode: TYPE 1-2-3
1. Press and hold the square program button until the small round LED light turns blue, then release. PROGRAM SET + PROGRAM SET + PROGRAM SET + PROGRAM SET +
2. The small round LED light will go out and the long LED light will begin flashing purple
Next, Proceed to step two or see alternate programming method
-OR-
For Genie® garage door opener and external receivers manufactured between 1995 to 2011
Placing the garage door opener into programming/ learn code mode:
1. Press and release the Learn Code button once. The red LED light will begin to blink.
Proceed to step 2
2- Programming the GL2T-BX flashlight remote to the Garage Door Opener
NOTE: Once the garage door opener is in programming/ learn code mode, you will have approximately 30 seconds to perform this next step.
Note: While programming the flashlight remote buttons stand at least five feet away from the garage door opener powerhead. This will ensure you have the proper communication between the flashlight remote and the garage door opener.
1. Slowly press and release the flashlight remote button that you are programming two times. The opener LED light will blink and go out, this indicates that you have successfully programmed your new flashlight remote.
2. Press and release that same button on the flashlight remote a third time and the garage door will open or close.
NOTE: It is possible to press the remote button too quickly or lightly. If the LED lights do not go OFF, then press the remote button a few more times to achieve confirmation.
3- Using the LED Flashlight
Press the LED Flashlight button on the remote once.
The LED Flashlight on the remote will operate until the flashlight button is pressed again or after 4 minutes have passed. After the 4 minutes is up, the LED light will flash indicating that light is going to turn off automatically.
Replacing the Battery
Replace the remote battery with 1-AAA battery.
1. Remove the screw and press down on top of the battery door and slide the back off of remote.
2. Match the battery polarity symbols (+/-) inside the battery housing and replace the battery.
3. Align the back cover with the remote, snap the case closed, and install the screw.
Questions & Answers
Ask a Question-
I purchased one of these sets and keep finding my garage doors open. Is there any way to make these things less sensitive? This is nuts. I can't have my garage door open all night, without my knowledge.
The most common cause for phantom operations would be a short in the wall button or shorted wall button wires (this can be caused by temperature changes, vibration, or power surges). or an issue involving the remote control or other wireless devices (keypad, built-in system in the vehicle).
Start troubleshooting by:
Removing the wall control wires and hard-wired keypad wires, if applicable, from the motorhead terminals. If unsure about which terminals on the operator powerhead are used for the wall control, consult the owner’s manual. This will eliminate both wires and the wall button. Leave disconnected for a reasonable amount of time to ensure that the problem is solved or reappears.
If the problem reappears while the wall control wires are disconnected, change the coding in the receiver and in the remotes. Leave them for a reasonable amount of time to ensure that the problem is solved or reappears
If the problem reappears, check for any stuck buttons on remote controls being used, and on any old remotes. remove the batteries from all remote controls. Again leave them inoperable for a reasonable amount of time to ensure that the problem is solved or reappears. Re-program or erase the receiver and re-program remotes (consult owner’s manual).
Check the down limit switch to make sure that it shuts the motor down after each operation. The door could be hitting the ground and automatically safety reversing. Always watch the door fully close and stop before driving off.
If the problem re-appears you would have a faulty circuit board that should be replaced.
If further assistance is required you can call us at 800-354-3643 and talk directly with a qualified Genie technician.
-
Will this work with model Pmx500ic/b?
Yes, it will.
-
Can this remote replace a GITR-3 remote?
Yes, it can!
-
Can’t get both working at the same time. When I program one the other stops working. Also using with wall button and home link in my car. Can you help!
It sounds like you have a garage door opener model that can hold up to seven wireless devices. This includes any old remotes or wireless devices that have been programmed. Once there is seven, any new remote programmed will kick the last one out that was programmed. To fix this, you can clear the receiver. To clear it press and hold the learn code button in until the red led light goes out. Then reprogram each wireless device back into the powerhead up to seven.
You can also call 1-800-354-3643 for programming assistance.
-
Will this remote work with Genie 2042?
Yes, it will!
-
Will this remote work with genie model isd995
Yes, it will!
-
I have a single and double garage overhead door model 696CD/B with a CodeDodger 2 button remote (round & triangular). Each button opens one door. Will these work as replacements, and how do I program them? Thanks
On these two button remotes, only the top button will work with the 696CD/B model garage door openers. If you are looking for a remote that can open both garage doors, I would recommend using the G3T-R, Single or Two-Pack.
-
Does it work Genie Model 2024 Professional Line
Yes, it does.
-
Is this compatible with “Linear LDO50”?
No, it is not.
-
Can you clip them on your visor in your car?
No, these do not come with the clips for the visor.
-
will these remotes work with Genie Pro screwdriver ? Model # CM7600C/A receiver model/ACSR3
Yes, they will.
-
Will this remote work with model H4000A genie intellicode?
Yes, it will.
-
Can this works on Genie GCG350L?
Yes, it will!
-
Will this remote work with Genie GCG350ML FCC B8Q ACSR1
Yes, it will!
-
Would this work on a IS550/A?
Yes, it will!
-
WILL THIS WORK ON THE MODEL NUMBER ACSR1G
Yes, it will.
-
Will this remote work on a model 1035?
Yes, it will!
-
I have 2 doors with Genie Pro 82 openers tombstone shape. Probably installed about 1991. I understand things changed in I993? Will these work for me?
The Genie Pro 82 model garage door opener used the fixed code style (dip switch) remotes. These will not work, you would need the GM3T-R, Genie Master Remote.
-
Will this work on model H6000A?
Yes, it will.
-
Is this remote compatible with Model # IC250/B, receiver ACSR1. Thanks
Yes, it is.
-
Will this work on model 2128B?
Hi Kimmy,
Yes this 2 Pack of 2 Button LED flashlight garage door opener remotes will work on your Genie garage door opener model 2128B -
Will this work on a 2020L model
Yes, it will.
-
Will this work pro 82 3/1 horsepower screw drive.
No, it will not. You would need a Genie Master Remote (GM3T-R) for the Pro 82 model garage door opener.
-
Is this remote compatible with. GICT390?
Yes, it is!
-
Will this work for model 2060L opener?
Yes, it will.
-
Will this remote control work with a Genie 1/3 hp model CM7600ic door opener?
Yes, it will.
-
Does the remote only work on genie products?
Yes, this remote will only work on Genie Intellicode model garage door openers.
-
I miss placed my garage door opener if I purchase this garage door opener can I program it to work without having the old ones ?
Yes, you can program this remote to any Genie Intellicode model garage door opener without having the old ones.
-
Will this remote GL2T-BX work with Genie opener Model 4063B-TKV?
Yes, it will.
-
Will this work with my Genie 3060?
Yes, it will!
-
Hi, I have the Genie Screw Drive garage opener, and have the garage opener remote with one button. I need another remote for my brother and was wondering if I purchase this remote and program it to my garage door opener, will it interfere with my current garage opener remote? Do I need to have to re-program that remote as well? Thanks
You can add a new Genie garage door opener remote and keep your old one working as well. You will need to program the new remote into the garage door opener.
-
Hello, will this work with a 1993 Genie Blue Max?
No, it will not. The Genie Blue Max would work with a Genie Master Remote (GM3T-R).