Skip to product information
1 of 2

The Genie Company

Control Board (6 Terminal Board) 36190S.S

Control Board (6 Terminal Board) 36190S.S

Regular price $85.99 USD
Regular price Sale price $85.99 USD
Sale Sold out

Configured circuit board for Chain Glide openers that have 6 terminals strip (models that have magnetic limits). This 6 terminal control board will get your garage door opener back up and running quickly once you have determined it needs to be replaced.

  • Compatible with models: 1020L, 2020L, GCG350, GCG350L, GCG350ML, H2000C-1, H2000C, PCG500ML, PCG700ML, PCG700FN, H2000C-1
  • Genuine Genie replacement part 
  • Comes with installation instructions for DIY replacement
  • Requires remote and limit re-programming with the new replacement board (see the instructions for details) 

SKU: 36190S.S

In Stock! Usually ships within 24 hours.

ASK A QUESTION View full details
Replacement garage door opener Control Board (6 Terminal Board) 36190S.S
Control Board (6 Terminal Board) 36190S.S
$85.99

QUESTIONS & ANSWERS

Ask a Question
  • I have a garage door opener pcg700ml with genie circuit board 34513 rev d 8-16-04 and the reprogram button doesnt work any more. Was looking on line at your Control Board (6 Terminal Board) 36190S.S and it says it will work in pcg700ml but the circuitry on the board looks a little different than mine. Yours does have the 7 terminals that i need but there is more blank space on the board, lol, so I want to make sure it will work

    Yes, the Control Board (6 Terminal Board) 36190S.S is compatible with Genie model PCG700ML.

  • The door looses power , no lights on sensors or the light on the unit but had 110 volt at receptacle. Sometimes it would come back. But nowit does not.

    If you have checked the outlet and there are no issues with it providing consistent power, this issue would most likely be due to a loose soldering point on the transformer and would require replacement of the Genie Control Board (6 Terminal Board) 36190S.S  assuming this is the correct board for your model.

  • My garage door opener was hit by a power surge. The transformer on the control board is blown and I'd like to replace it. I have 34513 Rev. D circuit board. Can you give me the part number or other specifics for the transformer only?

    Sorry we don't sell the transformer separately, or have the specifics available.  We would have to recommend replacing the circuit board.  

    Thank you.

  • Need to replace a 34513 Rev. D circuit board. You show a 36190S.S as a replacement. There is an extra knob above the two force knobs. There is no hole in my panel for this knob. Can this knob be removed?

    Yes, in fact you must remove this black knob/button cover on certain series models.  Yours is one of these.

  • Need circuit board for 2003 vintage PCG 700ML. Please advise as to part number. Want to verify what I see on this website. Nice website! Board wiped out by power surge 15 years ago and have done without for too long. Obviously, the unit is in good shape except for the board.

    The PCG700ML model garage door opener would use the 36190S.S circuit board.

  • I just replaced the circuit board with the 36190s.s. I would like to see how thw photo cell, limit switch, and wall control conect to the new board. I need to know which wire goes where on the terminal board.

    You can view the replacement instructions here
    The 6 terminals wires as follows: 
    1 and 2- wall console
    2 and 3- safe-t-beams
    4 and 5 - open limit switch
    5 and 6 - close limit switch

  • I have a PCG700ML chain glide. Circuit card learn button not working, 6 terminals with # 34514R. Does 36190S.S circuit card work. Please advice. Thanks.

    Yes, the 36190S.S will work with the PCG700ML model garage door opener.

  • Does the 36190S.S board replace the 34514T as others have suggested? Just want to confirm before ordering it. Thanks.

    Yes, it will, but the more direct replacement would be the 36190T.S (3 terminal) the 36190S.S is the 6 terminal. (either one will work) 

  • I have a genie 2020 opener. Need a new circuit board. Looks like the part number is 35917 on the board but I don’t see it listed in your replacement parts. Please advise.

    The Genie 2020L model garage door opener uses the 36190S.S circuit board.

  • Do you have Control board compatible with Genie H6000-7 model.

    There are three circuit boards in the Genie Model H6000 unit. I will list links below for all three. You can click on the links to see pictures and further details. 

    Genie Sequencer Board 20386R.S – The Genie Company
    Genie Intellicode® Receiver Board 36521R.S – The Genie Company
    Genie Opto-Luctor 31057R.S – The Genie Company

  • Is the learner button on control panel

    Yes, the learn code button is at the bottom of the Control Board (6 Terminal Board) 36190S.S.

PDF Instructions for replacing the 36190S.S control board 

Below are two sets of instructions depending on which model garage door opener you have that you are replacing the 36190S.S circuit board on. The first set is for Chan Glide Models, below that is for Chain Drive Models. 

36190S CONTROL BOARD INSTALLATION INSTRUCTIONS

Replacing the control board for CHAIN GLIDE MODELS
GCG 350/350L/350ML, PCG 400/450/500ML/600/650/700ML OCG 510/550/600ML/710/750/800ML

Tools Required: 1/4” nut driver or socket, Phillips and straight blade screwdriver.

1. UNPLUG operator from 110V outlet (if the unit is permanently wired, shut off power to the unit). Open light lens and remove with motor cover (one screw) to expose control board, Fig. 1.

2. REMOVE wall control, photocell and limit switch leads (on ML models) from front terminal strip, Fig. 2.

3. REMOVE rear control board mounting bracket and 2 mounting screws at top edge of control board, Fig. 3.

4. UNPLUG wire harness and remove existing control board, Fig. 4.
NOTE: ML models do not require the following modification of the front panel as shown, Fig. 5.

5. REMOVE the three knockout covers in terminal positions 4, 5 and 6 with the straight screwdriver, Fig. 5. They must be removed to make room for the additional terminals on the new board (used only on ML models).

6. RE-CONNECT wire harness and replace with the new 36190S.S control board. Make sure board is properly seated in the front panel support details and replace the mounting bracket. Securely tighten screw. Replace mounting screws at top edge and tighten snugly (DO NOT OVER-TIGHTEN. This can cause the board to crack).

7. REPLACE motor cover and light lens.

8. RE-CONNECT wall control, photocell and limit switch leads. Do this BEFORE re-connecting main power.

9. REPLACE the motor cover. (Control boards can be light sensitive and should not be operated while uncovered.)

10. PLUG IN power cord to 110V outlet (or reset breaker).

11. ADJUST up and down force controls and program transmitter devices per the owner’s manual.

NOTE: ChainGlide models do NOT require the use of the limit switch key cap included with this kit. 

Replacing the Genie Control Board 36190S.S for ChainGlide models

 

36190S.S Control Board Installation Instructions

Replacement Board for CHAIN DRIVE MODELS 

IC 250B, PMX 300/500 ICB, 496/696 CD/B

Tools Required: 1/4” nut driver or socket, straight blade screwdriver.

1. UNPLUG operator from 110V outlet (if the unit is permanently wired, shut off the power to the unit) and remove side cover (4 screws) to expose control board, Fig. 1.

2. REMOVE wall control and photocell leads from terminal strip, Fig. 2.

3. REMOVE control board mounting bracket at right edge of control board and 2 small mounting clips at top edge, Fig. 3.

4. UNPLUG wire harness and remove existing control board, Fig. 4.

5. INSTALL control board mounting clips and limit switch key cap on replacement board, Fig. 5.

6. REMOVE the three knockout covers in terminal positions 4, 5 and 6 with the screwdriver, Fig. 6. They must be removed to make room for the additional terminals on the new board (used only on other models).

7. RE-CONNECT wire harness and replace control board. Make sure board is properly seated in the rear panel support details and replace the mounting bracket. Securely tighten screw. Replace screws in mounting clips and tighten snugly (DO NOT OVER-TIGHTEN. This can cause the clips to crack).

8. REPLACE side cover. (Control boards can be light sensitive and should not be operated while uncovered.)

9. RE-CONNECT wall control and photocell leads. Do this BEFORE re-connecting main power.

10. PLUG IN power cord to 110V outlet (or reset breaker).

11. ADJUST up and downforce controls and program transmitter devices per the owner’s manual.

36190S.S Genie control board replacement for chain drive models

  • Shipping Truck

    Free Shipping

    We offer FREE shipping and handling on all orders that total over $17.99 and are shipped to a US address. All orders are shipped using UPS ground, directly from The Genie Company.

  • Genuine Genie Accessories and Parts

    Genuine Replacements

    Buying GENUINE Genie accessories and parts guarantees that you are getting quality OEM materials backed by a Genie warranty.

  • Customer support chat

    Support

    Need assistance? We are here for you! We offer a wide range of customer support options including contact by phone or email, web chat services with a live agent, and a robust support section also located on our website.  All customer care teams and services are based in the USA.

FREE SHIPPING ON ALL US ORDERS 17.99 AND UP