How to Program Your Genie 3-Button Remote – Model G3T

How to Program Your Genie 3-Button Remote – Model G3T

The popular G3T Genie garage door opener remote features Genie Intellicode Technology which keeps your garage secure by changing the access code every time you use it.  This opener works with up to 3 Genie garage door openers manufactured from 1997-present.  The top 2 buttons of the G3T remote will work with Genie garage door openers manufactured from 1995-1997.  

You can also program your Genie G3T Remote to your built-in car wireless control systems, HomeLink or Car2U.  This Genie garage door opener remote replaces the old remotes pictured below.

Follow the below instructions on how to program your Genie G3T garage door opener remote.  

A video with step-by-step instructions can be found here.

PDF Instructions found here.

Genie g3t

Step 1 - Putting the Garage Door Opener into Programming Mode

New Genie® Garage Door Openers

1. Press and hold the program button until the round LED turns blue, then release.

2. The small round LED light will go out and the long LED will begin flashing purple.

Proceed to step 2.   

                                -OR-

Genie® Openers and External Add On Receivers that were Manufactured between 1995 to 2011

1. Locate the Genie garage door opener learn button. Press & Release the Learn Code button once. The red LED will begin to flash. 

Proceed to step 2.

 

Step 2- Programming the (G3T) 3-Button Remote to your Garage Door Opener

NOTE: Once in programming mode, you will have approximately 30 seconds to perform this step

1. Pull the protective battery tab from the remote.

Image removing pull tab from a new G3T-R Genie remote

Note: While programming remote buttons, stand at least 5 feet away from the opener. This ensures you have proper communication between the remote and the opener.

2. Slowly press and release the remote button of your choice two times. The opener LEDs will flash and go off, indicating you have successfully programmed your remote.

3. Press and release the same button a third time and door will open or close. It is possible to press the remote button too quickly or lightly. If the LEDs do not go OFF, press the remote button several more times to achieve confirmation.

 

Lost or Stolen Remote/Erasing all Remotes

Newer Genie® Garage Door Openers

1. Press and hold the program button until the round LED turns blue, then release.

2. Press and hold the Up(+) Down (-) buttons at the same time, until both LEDs flash blue and go OFF.

Genie® Garage Door Openers and External Receivers Manufactured between 1995 to 2011

• To erase all of the remote devices from other types of Genie® garage door openers, Press and hold the Learn Code Button until the LED stops blinking.

Start at step 1 to reprogram your remotes.

NOTE: Clearing remote control memory from the power head will clear ALL programmed remotes and keypads. Your opener will no longer recognize any signal from any remote device, including a missing remote device.

 

Replacing the Remote Battery

Replace the G3T remote battery with CR2032 coin cell battery.

1. Open the remote case using a washer or coin that fits into the slot at the top of the remote.

Image replacing battery on a G3T-R Genie 3 Button remote

2. Replace the battery. Match battery polarity symbols inside the battery housing.

3. Align components and snap case closed.

 

NOTE: For openers manufactured between 1995-1997, use the two upper buttons on the remote. Made after 1997 - use any button for programming.

Back to blog

41 comments

how to i erase all 3 buttons on my genie remote.
just from the hand remote unit

mo cassim

@Walter Altorfer – You can view the video and instructions for programming Homelink here: https://www.geniecompany.com/homelink-programming

Heather Rothacher

There are lots of videos and dialogue on programming the remote. But nothing on how you program the remote to the button under the rear view mirror in the car. I just bought a new Genesis and am having difficulty in getting the button in the car to open the garage door. Any ideas?

Walter Altorfer

@Ryan – The G3T remote will work with the 1125 model garage door opener. If you are saying you have a new G3T remote, and trying to program it to the 1125, we would be happy to assist you if it is not working. Please contact our Genie customer service at 1-800-354-3643 or visit or support portal to chat at https://support.geniecompany.com/.

Heather Rothacher

I’m having the same problem John has believe. My new Genie 1125 opener flashes purple but when I press the button on my G3T remote, the small LED starts flashing purple. The included remote works fine and my ford home link works. Very frustrating a genie opener and a genie multifunction remote don’t work together.

Ryan

Leave a comment

Please note, comments need to be approved before they are published.