The Genie Company
Intellicode® Receiver Board 36521R.S
Intellicode® Receiver Board 36521R.S
Couldn't load pickup availability
Intellicode receiver replacement circuit board that works certain Genie model garage door openers. This receiver board controls the wireless devices that work with the opener. Use this replacement board to get your wireless devices working again once you have determined the receiver circuit board will need replacing.
- Compatible with Models:  1060, 1560, 2560, 3560, 3860, IC250, IS525, IS525/B, IS550, IS550/B, IS850, IS900, IS900/B, IS920/A, CM7600, CM8600, PRO95, CM8600-FN, 2060L, 3060L, H4000, H6000, IMS1000, ISL950, ISL950/B, ISL980, ISL980/B
- Genuine Genie replacement partÂ
- Requires re-programming with the new boardÂ
SKU: 36521R.S
UPC:
In Stock! Usually ships within 24 hours.
ASK A QUESTION View full details
PDF Instructions for replacing the 36521R.S circuit board
REPLACEMENT RECEIVER BOARD (36521R.S) INSTALLATION INSTRUCTIONS
For 390 MHz AC Screwdrive Models
WARNING
Moving door can cause serious injury or death.
• During this procedure, the Door Opener could begin to run. Stay away from moving Door and its parts. To keep Door from moving, close Door and disconnect it from Opener by pulling Emergency Release Cord.
• Keep people clear of opening while the door is moving.
• Do Not allow children to play with remote control or door opener.
• Do Not operate a door that is jammed or has a broken spring.
If safety reverse does not work properly:
• Close door/disconnect opener by pulling Emergency Release Cord.
• Do Not use the remote control or door opener.
• Refer to Door and Door Opener Owner’s Manuals or Instructions.
WARNING
BE SURE ELECTRICAL POWER HAS BEEN DISCONNECTED FROM THE INPUT POWER LINES PRIOR TO REMOVING THE ELECTRIC BOX COVER. AN APPROPRIATE LOCKOUT/TAGOUT PROCEDURE IS RECOMMENDED. INSURE THE DOOR IS CLOSED PRIOR TO REMOVING THE OPERATOR. TEST THE DOOR FOR PROPER OPERATION AND CORRECT ANY MALFUNCTIONS PRIOR TO REINSTALLING THE OPERATOR.
Tools Required: 1/4” nut driver or socket, and/or Phillips screwdriver.
1. UNPLUG operator from110V outlet. If the unit is permanently wired, open the circuit breaker. If you are unsure about how to shut off power to the unit, call a licensed electrician in your area. Do not reconnect power until instructed to do so.
2. REMOVE the 2 upper light cover screws and let light cover flip down. FIG 1
3. LOOSEN but do not remove the 4 motor cover screws and remove the motor cover. FIG 1
4. REMOVE and retain the receiver mounting screw. FIG 2
5. UNPLUG wire harness from receiver board. Note harness orientation (Green wire on left facing the connector). FIG 3
6. INSTALL the 36521R.S receiver board to bracket and install the mounting screw. FIG 2
7. RECONNECT wire harness to replacement receiver board. FIG 3
8. FEED antenna wire through the hole in the front panel and point down through light cover. FIG 4
9. REPLACE motor cover.
10. PLUG power cord to outlet (or reset breaker).
11. ADJUST up and downforce controls and program transmitter devices following all safety and operating instructions in the owner’s manual.
12. FLIP lens cover up and attach 2 light lens screws.
-
Free Shipping
We offer FREE shipping and handling on all orders that total over $17.99 and are shipped to a US address. All orders are shipped using UPS ground, directly from The Genie Company.
-
Genuine Replacements
Buying GENUINE Genie accessories and parts guarantees that you are getting quality OEM materials backed by a Genie warranty.
-
Support
Need assistance? We are here for you! We offer a wide range of customer support options including contact by phone or email, web chat services with a live agent, and a robust support section also located on our website. All customer care teams and services are based in the USA.
