37222R - Series III Wall Console Installation Instructions

PDF Series III Wall Console Installation Instructions 

Series III Replacement Wall Console, 37222R Installation 

1. IMPORTANT INFORMATION

Use only the Series III wall console with Genie® garage door
openers models 2562, 2564, 3022, 3024, 3042, 3062, 3064, 4022,
4024, 4042, 4062, and 4064 that were from 2010 through 2012 with Series III electronics. The serial number will be lower than 122494110518.  If you currently have a series III wall console and have not replaced the circuit board, this will work. If you are unsure, please contact Genie customer service at 1-800-354-3643. 

SERIES III WALL CONSOLE - OPERATION AND FEATURES

Wall console has three buttons and one indicator light.

Indicator Light
Indicator light will display red when wall console is properly wired and Sure-Lock™ is OFF. When Sure-Lock™ is ON indicator light flashes.

Open/Close Button
Use this button to open or close garage door. When Sure- Lock™ is ON the Open/Close button will CLOSE door only. Note: Constant button pressure in the CLOSE mode will override error responses in the powerhead and close door.

Independent Light Console Button
Use this button to turn powerhead lights ON. Powerhead lighting will remain ON until this button is pressed again or a door action has been completed. Note: If opener has a Motion Detector, the sensor will keep powerhead lights ON as long as motion is detected.

Sure-Lock™ Button
When Sure-Lock™ is ON the powerhead cannot be activated by the wall console or a remote.
• Press and hold for 5 seconds (or until Indicator Light flashes) to activate Sure-Lock™.
• Press and release to turn Sure-Lock™ OFF.

WARNING

• Verify there is NO power to the opener before installing wall console and/or wall console wires.
• Use of any other wall console can cause the door to operate unexpectedly and the light not to work. Use only the included wall console.

CAUTION

• Staples which are too tight can cut or pinch wires. Cut or pinched wires can cause the wall console to stop working. When using the insulated staples, make sure you fasten them only as tightly as needed to hold the wire snugly.

Series III Wall Console - Replacement

Use these instructions when replacing a Series III wall console.

1. Install Replacement Wall Console
• Disconnect power to powerhead.
• Remove wires from existing wall console.
• Split and strip ends of wire if required (Fig. 2).
• Fasten wire to control board screws on back of wall console (Fig. 3).
– Striped wire to the + (plus) terminal
– White wire to the - (minus) terminal
• Mount wall console to wall using screws provided.
• Reconnect power to powerhead.
• Check operation of each wall console button and feature.

 

Series III Wall Console - Expansion

Use these instructions when you are expanding or adding to an existing Series III wall console.

1. Wall Console Wiring (in series or in parallel)
• Disconnect power to powerhead.
• Pick a convenient location for mounting new wall console
NOTE: Securely anchor wires to ceiling and wall using insulated staples (Fig. 5). Staples should be snug only.
• (in series) Run wire from new wall console to existing wall console (Fig. 7).
– Split and strip ends of wire (Fig. 2)
– Fasten wire to control board screws on back of existing wall console.
Striped wire to the + (plus) terminal
White wire to the - (minus) terminal
• (in parallel) Run wire from new wall console to powerhead (Fig. 8).

– Route wire through wire guide on powerhead (Fig. 6)
– Split and strip ends of wire (Fig. 2)
– Insert wire into terminal holes and lightly press in the locking clips above each terminal hole (Fig. 8)
– Confirm wire lock by lightly tugging on the wire. Wire should remain in the terminal hole.

2. Fasten wire to control board screws on back of new wall console (Fig. 3).
Striped wire to the + (plus) terminal
White wire to the - (minus) terminal

3. Reconnect power to powerhead.
• Check operation of each button and feature of both wall consoles.