Programming the Genie GUK-BX Universal Wireless Keypad Video

Genie Universal Wireless Garage Door Opener Keypad Programming Instructions 

Alternative Programming Instructions (Fixed Code Models) 

Genie Universal Keypad Compatibility Chart

Universal Keypad Instructions

IMPORTANT FEATURES OF THIS KEYPAD:

•  An audible beep will sound with every key pressed.
• Keypad will operate up to 3 doors with one PIN number.
• A temporary PIN can be set for convenient non user access.
• Do not press the LEARN button for longer than the noted 2-3 seconds as it could cause the operational remotes to no longer work.

STEP 1 - FIND SPECIFICATIONS & LEARN/PROGRAM BUTTON

1. Locate the brand and opener/receiver specifications for the device by consulting the label on the opener/receiver, the instructions manual, the current remote controls for the opener, or the original manufacturer or the opener/receiver.
2. Find the LEARN/PROGRAM button on the device - shape, color or name of this button could vary by brand. For garage door openers, be sure to check under the light covers. For commercial openers, this button may be on the circuit board or the opener. In some cases, this button could also be on an external receiver that is mounted on or nearby the product. Consult the devices manual if needed.

STEP 2 - CLEARING THE KEYPAD

Perform this task first before setting the PIN or at anytime the keypad needs to be reset to its factory default:

1. Remove activation tab from inside battery compartment.
2. Press both the PROGRAM & UP/DOWN keys at the same time and hold for 5 seconds. (tone will sound) - then release (green LED will flash and go out).
3. The keypad is now ready to be programmed. Start at STEP 3.

If the opener/receiver has dip switch technology, please move to the alternate instructions listed on our website at this time: www.geniecompany.com/dipswitchesGUK

STEP 3 - PROGRAMMING TO ONE OR MORE OPENERS

This keypad can be programmed to up to 3 individual garage door openers in any combination of manufacturer specifications. You will need your opener ID# from Chart A for these steps. To start over at any time, start at STEP 2 - CLEARING THE KEYPAD.

IMPORTANT: For ID#4 Chamberlain®/LiftMaster®/Craftsman® Yellow Learn Button ONLY, move to NEXT SECTION.

PROGRAM OPENER #1  (For all openers EXCEPT ID#4 Yellow Learn)

1. On the keypad, enter a personal PIN (3-8 digits)
2. On the keypad, press and release the UP/DOWN key (LED flashes slowly).
3. On the keypad, enter the ID# of the opener from Chart A.
4. On the keypad, press and release the UP/DOWN key (LED flashes rapidly).
5. On the opener, press the LEARN/PROGRAM button for 2-3 seconds and then release.
6. On the keypad, press the UP/DOWN key once every two seconds until the opener operates. DO NOT press any additional buttons until the opener stops running
7. WAIT until backlighting is out before attempting additional keypad entries. Programming is complete

ONLY for ID#4 Chamberlain®/LiftMaster®/Craftsman® Yellow Learn: PROGRAM OPENER #1

1. On keypad, enter personal PIN (3-8 digits).
2. On keypad, press and release UP/DOWN key (LED flashes slowly).
3. On keypad, enter the ID#: 4
4. On keypad, press and release UP/DOWN key (LED flashes rapidly).
5. Then press and hold down UP/DOWN key.
6. Release button after tone sounds (5 sec).
7. On opener, press LEARN/PROGRAM button 2-3 seconds and then release.
8. On keypad, press UP/DOWN key ONE time. Opener will click.
9. On opener, press LEARN/PROGRAM button 2-3 seconds again and then release.
10. On keypad, press UP/DOWN key again ONE time. Opener will click.
11. On keypad, press UP/DOWN key again ONE time. Opener will operate.
12. WAIT until backlighting is out before attempting additional keypad entries. Programming is complete.

MULTIPLE OPENERS: Complete steps for Opener #1 above. To program Opener #2 or #3 at any time, follow the steps below. Be ready to reference Chart A and then #3 from above:

1. . With keypad backlighting off, press the PROGRAM button 2 times to program a second opener OR press it 3 times to program a third opener (blue LED flashes slowly).
2. . With blue LED still flashing, return to #3 in the section above and enter its opener ID# from CHART A.
3. Continue with the remaining numbered steps.

TIP: As soon as the opener activates, DO NOT press any additional buttons until the opener stops running.

Genie® and Intellicode® are registered trademarks of The Genie Company. All other listed names and trademarks are the property of their respective owners.

SINGLE DOOR OPERATION:

1. Ensure number pad back lighting is of
2. Enter PIN
3. Press the UP/DOWN key.
4. Opener will operate.

MULTI-DOOR OPERATION:

1. Ensure number pad back lighting is of
2. Enter PIN.
3. . Press the UP/DOWN key
4. Press number key corresponding with desired door (1, 2, or 3).
5. Desired opener will operate

ADDITIONAL PROGRAMMING

SETTING A TEMPORARY MAIN PIN:

If the keypad is to be used by normally unauthorized personnel (such as a repairman) a temporary PIN can be assigned to that personnel to gain access to the garage. This PIN will remain active until the main PIN is used again. (PRGM = PROGRAM).

1. Enter main PIN.
2. Press PRGM key three times (LED will turn solid indicating keypad is ready for temporary PIN).
3. Enter temporary PIN (3-8 digits)
4. Press PGRM key one time (LED will blink twice and go out indicating a temporary PIN is set).
5. To cancel the temporary PIN, operate the keypad/door with the original main PIN.

CHANGE PIN:

If the main PIN needs changed, follow these steps

1. Enter current main PIN.
2. . Press PRGM key one time (LED will turn solid indicating keypad is ready for new PIN).
3. Enter new PIN (3-8 digits).
4. . Press PGRM key one time (LED will blink twice and go out indicating a new PIN is set).

MOUNTING KEYPAD/REPLACING BATTERIES

Keypad MUST be mounted within sight of the garage door(s) at least 5 feet above floor and clear of any moving door parts. NOTE that programming will not be lost during battery removal.

1. Remove battery cover and batteries. Replace if necessary. NOTE: Only use standard or alkaline AAA batteries. DO NOT use rechargeable batteries.
2. Drill a 3/32” pilot hole for the top mounting screw
3. Install included screw into pilot hole, leaving 1/8” gap between the screw head and wall.
4. Hook the slotted mount on back of keypad over the screw.
5. Mark and drill a 3/32” pilot hole for the bottom screw and secure keypad to the wall. (Do not over-tighten).
6. . Reinstall batteries.

1. How many different openers can you control with the Genie Universal Keypad? 

• With the Genie Universal Keypad, you can control a combination of up to 3 different garage door openers. Each of the 3 openers can be programmed individually of the others so having multiple brands of openers controlled by a single keypad is not a problem.

2. Are any manufacturer settings of the Genie Universal Keypad preprogrammed?

• No, the Genie Universal Keypad does not come pre-programmed with any
  specific manufacturer brands/specifications.

3. Does the Genie Universal Keypad have a pre-programmed PIN number?

• No, the Genie Universal Keypad does not come with a pre-programmed PIN
  number. The PIN number for the keypad is set during programming.

4. What kind of batteries does the Genie Universal Keypad use?

• The Genie Universal Keypad uses 2xAAAs. You can access the batteries by
  removing the battery cover on the front lower portion of the keypad.

5. Why does the keypad beep every time I press a button?

• The Genie Universal Keypad will emit a tone each time a button on the keypad is properly pressed. This gives the user an audible sound to confirm their button
  the press has been received by the keypad.

6. Why does the Genie Universal Keypad operate the door without the PIN?

• The Genie Universal Keypad will stay active for 15 seconds after the door has
  moved for security reasons (should you need to move the door again quickly).

7. What openers are compatible with the Genie Universal Keypad?

• Control the most popular brands of garage door openers such as Genie®, Overhead Door®, Chamberlain®, Linear®, Wayne Dalton®, plus many more! Over time, we will implement additional manufacturers which means the
  compatibility list can and will change. You can use this link to find the most up-to-date compatibility chart.

8. Will the Genie Universal Keypad work with any other brands/specifications other than what is on this list?

• For rolling code brands/specifications, no, the keypad will not work on any other brands/specifications other than what is listed. For dip switch
  brands/specifications, it is possible if they are on the same MHz, however,
  without proper testing of individual units, this cannot be confirmed. Also, please
  remember, Genie operator accessories should only be used on products
  produced 1993 and after that have functional safety sensors.

9. Does the Genie Universal Keypad use dip switches?

• The Genie Universal Keypad does not use physical dip switches, but it does use
  “virtual dip switches” – or dip switch codes created by using specific button
  presses on the keypad. Once in the mode to receive dip switch input, the user
  will press 1=UP, 2=MIDDLE, and 3=DOWN to represent the location of trinary dip switches or 1=UP, 2=DOWN for binary dip switches.

10. How do I clear out the Genie Universal Keypad and return it to the factory
settings?

• Press both the PROGRAM & UP/DOWN keys at the same time and hold for 5
  seconds (a tone will sound) - then release both buttons. The green LED will flash
  and go out. Perform this task first before setting the PIN or at any time the keypad needs to be reset to its factory default.

11. When working with Chamberlain®/LiftMaster®/Craftsman® Yellow Learn Button units, I am having trouble programming the universal keypad to the operator head/receiver.

• When programming a Chamberlain/LiftMaster/Craftsman operator with the yellow learn button, be sure to follow the specific programming instructions for these units. After preparing the keypad to receive a yellow learn button unit, on the garage door opener:
  1. Press the yellow LEARN button for 2-3 seconds and then release
  2. On the keypad, press and release the UP/DOWN button once every 2
  seconds until the garage door opener operates. Let it run until it stops.
  TIP: As soon as the opener activates, DO NOT press any additional buttons until the opener stops running.
  3. With the keypad backlight still flashing, repeat steps 1 and 2 above.
  TIP: As soon as the opener activates, DO NOT press any additional buttons until the opener stops running.
  Programming is complete.

12. What is the trick when working with Marantec® products?

• If there are no other remotes or keypads being used with the Marantec opener,
  follow the Genie Universal Keypad instructions to program.
  If you already have a Marantec remote(s) paired to the operator and you program the Genie Universal Keypad, the keypad will work the opener, but the existing remote(s) will not.
  In order to use a Genie Universal Keypad with a Marantec opener, you will need
  to use a Genie Universal Remote as well. The TEACH & PAIR METHOD in
  universal remote instruction can use the universal keypad you just paired to the
  opener as the ‘existing operational remote’ and learn the proper code from the
  keypad. When the TEACH & PAIR METHOD instructions call for the existing
  operational remote, use the paired universal keypad in its place.

13. When working with any of the dip switch style units, do I still need to
program the keypad to the opener head?

• After entering the converted dip switch code into the keypad, there is no need to program to the opener head. When the UP/DOWN key is pressed, the opener will operate, and programming is complete.

Shop the Universal Garage Door Opener Wireless Keypad