Control Board (6 Terminal Board) 36190S.S

I have a garage door opener pcg700ml with genie circuit board 34513 rev d 8-16-04 and the reprogram button doesnt work any more. Was looking on line at your Control Board (6 Terminal Board) 36190S.S and it says it will work in pcg700ml but the circuitry on the board looks a little different than mine. Yours does have the 7 terminals that i need but there is more blank space on the board, lol, so I want to make sure it will work

Yes, the Control Board (6 Terminal Board) 36190S.S is compatible with Genie model PCG700ML.

The door looses power , no lights on sensors or the light on the unit but had 110 volt at receptacle. Sometimes it would come back. But nowit does not.

If you have checked the outlet and there are no issues with it providing consistent power, this issue would most likely be due to a loose soldering point on the transformer and would require replacement of the Genie Control Board (6 Terminal Board) 36190S.S  assuming this is the correct board for your model.

My garage door opener was hit by a power surge. The transformer on the control board is blown and I'd like to replace it. I have 34513 Rev. D circuit board. Can you give me the part number or other specifics for the transformer only?

Sorry we don't sell the transformer separately, or have the specifics available.  We would have to recommend replacing the circuit board.  

Thank you.

Need to replace a 34513 Rev. D circuit board. You show a 36190S.S as a replacement. There is an extra knob above the two force knobs. There is no hole in my panel for this knob. Can this knob be removed?

Yes, in fact you must remove this black knob/button cover on certain series models.  Yours is one of these.

Need circuit board for 2003 vintage PCG 700ML. Please advise as to part number. Want to verify what I see on this website. Nice website! Board wiped out by power surge 15 years ago and have done without for too long. Obviously, the unit is in good shape except for the board.

The PCG700ML model garage door opener would use the 36190S.S circuit board.

I just replaced the circuit board with the 36190s.s. I would like to see how thw photo cell, limit switch, and wall control conect to the new board. I need to know which wire goes where on the terminal board.

You can view the replacement instructions here. 
The 6 terminals wires as follows: 
1 and 2- wall console
2 and 3- safe-t-beams
4 and 5 - open limit switch
5 and 6 - close limit switch

I have a PCG700ML chain glide. Circuit card learn button not working, 6 terminals with # 34514R. Does 36190S.S circuit card work. Please advice. Thanks.

Yes, the 36190S.S will work with the PCG700ML model garage door opener.

Does the 36190S.S board replace the 34514T as others have suggested? Just want to confirm before ordering it. Thanks.

Yes, it will, but the more direct replacement would be the 36190T.S (3 terminal) the 36190S.S is the 6 terminal. (either one will work) 

I have a genie 2020 opener. Need a new circuit board. Looks like the part number is 35917 on the board but I don’t see it listed in your replacement parts. Please advise.

The Genie 2020L model garage door opener uses the 36190S.S circuit board.

Do you have Control board compatible with Genie H6000-7 model.

There are three circuit boards in the Genie Model H6000 unit. I will list links below for all three. You can click on the links to see pictures and further details. 

Genie Sequencer Board 20386R.S – The Genie Company
Genie Intellicode® Receiver Board 36521R.S – The Genie Company
Genie Opto-Luctor 31057R.S – The Genie Company

Is the learner button on control panel

Yes, the learn code button is at the bottom of the Control Board (6 Terminal Board) 36190S.S.